One-design race shop · Dinghy
X-Boat Race Shop
Everything you need to prepare, compete, and win.
Fit verified for X-Boat
All X-Boat equipment
4 parts
Fit verified for X-Boat
Forespar
Forespar Spinnaker Pole 1 in. Dia., 6 ft. max. length (for Small dinghies) - Nylon/Nylon Ends
Part # FOR303600
$159.96
$199.95Fit verified for X-Boat
Spinlock
Spinlock Rig Sense Tension - Wire: 1/16 - 3/16 in (2.0 - 5.0 mm)
Part # SPI-RGS-0205
$143.65
$169.00
No X-Boat parts match these filters.
Can’t find a part for your X-Boat? Request a X-Boat part
Go fast
X-Boat tuning guide
The Melges X-Boat is set up with three rake settings (21' 0" down to 20' 10"), snug sidestays and a downhaul car read against the mast's black band, then board height and vang by wind. North's and Quantum's guides come from the same Zenda team and match almost word for word; the difference is that North heads its wind ranges in mph and Quantum in knots. A SailZing compilation adds StaMaster turns by wind but uses a slightly different light-air rake, jib-lead and board settings.
Quantum Sails (Melges) — Melges X-Boat Tuning Guide © 2020
- Written for
- Quantum X-Boat main and jib
- Tension gauge
- None: sidestays snug
- How it’s measured
- Measure rake on the trailer, in light air, with the jib up (reference points not given). Many sailors set rake too far forward.
- Source
- Quantum Sails (Melges), © 2020
Base setup
- Heel
- Under 5 kn a little leeward heel; over 5 kn completely flat
- Jib lead (base)
- With tracks installed as in Quantum's diagrams, all the way aft with two holes showing behind the car; set so the jib luffs evenly top to bottom when luffed head to wind (breaks high first: lead too far aft; low first: too far forward)
Settings by wind (knots)
| Setting | 0–5 kn | 6–15 kn | 16–25 kn |
|---|---|---|---|
| Mast rake (sidestays snug) | 21' 0" | 21' 0" at 6–10 kn; 20' 11" at 10–15 kn | 20' 10" |
| Downhaul car / cunningham | Car top above the black band, wrinkles showing, cunningham off | Car to the top of the black band; cunningham if you can't hold the boat down | Car top at the bottom of the black band; cunningham hard upwind, off downwind |
| Vang | Loose | Fairly tight at 5–10 kn, much tighter at 12–15 kn | Head up, sheet in hard, then vang hard (vang-sheet upwind) |
| Centreboard | All the way down (as deep as possible without hitting the box) | All the way down; up 3–4" at 15 kn with big chop | Up 4–5" |
| Jib luff | Eased, wrinkles showing | No wrinkles | Tight and smooth |
| Main trim | Upper batten parallel to the boom; in a drifter boom out to the transom corner | Top batten parallel to the boom | Ease as much as needed (up to 4 ft) to stay flat |
| Jib trim | Loose so the top batten twists off; lead may go 1–2 positions forward | Harder; keep the top-batten telltale flowing; lead in normal position | Tight, leech telltale flowing; lead 1–2 positions aft to twist the head |
Trim by condition
- Heavy air
- Pinching or heading up won't buy speed: keep the boat flat and ease the main.
- Sail care
- Minimise jib flogging, roll the sails and don't fold the windows.
- The PDF prints the rake values without foot/inch marks ("21 0", "20 11", "2010"); they are read here as 21' 0", 20' 11" and 20' 10", matching North's guide.
North Sails — X Boat Tuning Guide Current web page, undated
- Written for
- North X-Boat main and jib (no models named)
- Tension gauge
- None: sidestays snug
- How it’s measured
- Measure rake on the trailer, preferably in light air with the jib up; don't set it too far forward.
- Source
- North Sails, Current web page, undated
Base setup
- Heel
- Sail flat once the wind is above 5 mph; don't sail too flat (or heeled to windward) in 0–5
- Jib sheet
- Don't ease the jib except a click at a time; steer and use the mainsheet to keep the boat flat
- Jib lead (base)
- All the way aft with two holes showing behind the car
Settings by wind (headings in mph; text uses knots)
| Setting | 0–5 mph | 6–15 mph | 16–25 mph |
|---|---|---|---|
| Mast rake (sidestays snug) | 21' 0" | 21' 0"; 20' 11" in 10–15 kn | 20' 10" |
| Downhaul car / cunningham | Car top above the black band, wrinkles, cunningham off | Car to the top of the black band; cunningham if you can't hold the boat down | Car top at the bottom of the black band; cunningham hard upwind, off downwind |
| Vang | Loose | Fairly tight at 5–10 kn, much tighter at 12–15 kn | Sheet in hard, then vang hard |
| Centreboard | All the way down | All the way down; up 3–4" at 15 kn in big chop | Up 4–5" |
| Jib luff | Wrinkles noticeable | All wrinkles gone | Tight, no wrinkles |
| Main trim | Upper batten parallel to the boom; drifter: boom to the transom corner | Top batten parallel to the boom | Ease as much as 4 ft if heeled; keep flat and driving |
| Jib trim | Loose, top batten twisting off; lead may go 1–2 positions forward | Harder; top telltale flowing aft; lead normal | Tight; lead 1–2 positions aft |
- Same settings as Quantum's guide, but the section headings are in mph while the rake and vang notes inside them are in knots.
SailZing (editor) — X-Boat Tuning Guide – Go Fast in all Conditions Published 26 Jun 2017
- Written for
- Not stated (built on North's guide)
- Tension gauge
- None: sidestays by StaMaster index numbers from a hand-tight base
- How it’s measured
- Rake: tape on the main halyard, hoisted and locked, measured to the transom, adjusted with the jib halyard. Sidestays: hand-tighten the StaMasters with the jib up at the light–medium rake, check the masthead-to-chainplate distances match on both sides, and record the index numbers as the base.
- Source
- SailZing (editor), Published 26 Jun 2017
Base setup
- Rake marks
- Mark the jib halyard and mast for "Light-Medium" (20' 11") and "Heavy" (20' 10")
- Sidestays
- Return to the base setting after sailing so the stays don't stretch
Summary by wind (mph)
| Setting | Light 0–8 | Medium 8–15 | Heavy 16+ |
|---|---|---|---|
| Mast rake | 20' 11" | 20' 11" | 20' 10" |
| Sidestays (StaMaster) | Base (hand-snug) | Tighten 1 index number | Tighten 2.5 index numbers (very tight) |
| Jib leads (holes showing, counted from the back of the track) | 4 | 3 | 2 |
| Cunningham / jib downhaul | Cunningham loose; jib luff wrinkles just out, foot touching the deck | Wrinkles out | Hard |
| Vang | Snug with the mainsheet in loosely | Tight with the mainsheet fully in | Head to wind, sheet in hard, then vang tight |
| Centreboard | Down | Up 2" | Up 4" |
Trim by condition
- Vang
- Re-set it if the wind changes a lot.
- A third-party compilation: the site says its numbers come from North's online guide plus unpublished information from Melges. It differs from North and Quantum on light-air rake (20' 11" vs 21' 0"), jib leads and board height.
- The rake steps say tightening the jib halyard increases rake, but then say to loosen it to reach the more-raked 20' 10"; the wording is inconsistent.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.Rig tension gauges for the X-Boat
Technical
X-Boat resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the X-Boat by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- We have no current one-design class rules on file for the X-Boat. Racing legality depends on your class or handicap rules; check them before changing equipment.