One-design race shop · Multihull
Hobie 14 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Hobie 14
All Hobie 14 equipment
6 parts
Fit verified for Hobie 14
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Hobie 14
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Hobie 14
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66
No Hobie 14 parts match these filters.
Can’t find a part for your Hobie 14? Request a Hobie 14 part
Go fast
Hobie 14 tuning guide
The Hobie 14 is a una-rig cat set up mainly with mast rake (measured by hanging a weight on the main halyard), a fairly loose rig that lets the mast rotate, batten tension, and then downhaul, outhaul and traveller by wind. There is no gauge: rig tension is judged by how far the leeward shroud can be twisted, and rake is chosen by skipper weight. Bob Curry's tips are the most detailed published numbers; they were written for the standard (jibless) 14, and Turbo owners on the forums have used different rake.
Bob Curry (via TheBeachcats.com) — Hobie 14 Catamaran Tuning Guide (Bob Curry's tips) Posted 24 Feb 2025 (same text as Curry's forum post headed "Updated: December 27, 2002")
- Written for
- Standard Hobie 14 mainsail
- Tension gauge
- None: rig tension by twisting the leeward shroud
- How it’s measured
- Rake: mast stepped on the trailer with the boat levelled (carpenter's level on the shroud chainplate); hang a 5 lb weight on the main halyard and measure from the halyard to the bottom of the mainsail cut-out in the mast. Rig tension: grab the leeward shroud and see how far it turns.
- Source
- Bob Curry (via TheBeachcats.com), Posted 24 Feb 2025 (same text as Curry's forum post headed "Updated: December 27, 2002")
Base setup
- Mast rake
- 45–57" depending on skipper weight (lighter = bigger number); Curry at 160 lb uses 55"
- Rig tension, not trapezing
- Loose: the leeward shroud can be twisted to 120°; tighten as the breeze builds so the leeward hull isn't pressed down, and more in chop
- Rig tension, trapezing
- Tight enough that the leeward shroud only twists to 45°, so the rig stays powered and doesn't dump in lulls
- Rake line
- Use the mast raker only downwind, to stop the rig banging
- Sail shape (Curry's design target)
- Draft at 45%, 16% camber; bottom 3 battens untapered, top 3 tapered and soft
- Rudder rake
- 1 5/8–1 3/4": measured 12" down from the bottom casting, from a line through the rudder pins
- Rudder toe-in
- 1/8" with the rudders locked down
Batten tension (sail on the trampoline, set bottom to top)
| Batten | Tension |
|---|---|
| #6 (bottom) | Almost standing up |
| #5 | Barely standing up |
| #4 | Standing up |
| #3 | Standing up |
| #2 | Barely standing up |
| #1 (top) | Almost standing up |
Traveller
| Situation | Traveller |
|---|---|
| Upwind, not trapezing | 5–6" out from centre (lets you foot fast) |
| Upwind, trapezing | No more than 3" out |
| Reaching | Out to the hiking strap |
| Deep reach / downwind | End of the track |
Trim by condition
- Downhaul
- Normally just enough to remove wrinkles; in very strong wind pull hard to bend the mast and free the leech.
- Outhaul
- As tight as possible and cleated: the foot is attached to the boom, so easing it doesn't help.
- Battens in chop
- A little more batten tension for power.
- Tacking (Curry, forum follow-up)
- Roll tack; ease about 12" of mainsheet through the eye of the wind in light air and 18–24" in more wind so the boat can complete the tack.
- Republished tips from Curry (1984 Hobie 14 World Champion), not a sailmaker document. The original 2002 post and Curry's follow-ups are at https://thebeachcats.com/forums/hobie-16-forum/hobie-14-updated-tuning-guide/.
- Turbo: Curry replied in that thread (Jan 2003) that he used the same tips on the Turbo, but a 2004 forum thread (https://thebeachcats.com/forums/hobie-16-forum/h14-turbo-mast-rake/) says the 55" figure was for the 14, not the Turbo, and reports second-hand that Curry later advised Turbo sailors to rake until the weighted halyard hangs about 10" in front of the rear crossbar. Treat the rake range as standard-14 numbers.
Hobie Class Association of North America (Boyd Bass & Bob Mimlitch) — Hobie 14 – Rigging and Tuning Guide (Hobie University) Hobie U, 31 Mar 2002
- Written for
- Standard Hobie 14 mainsail
- Tension gauge
- None
- How it’s measured
- No measurements: settings are described by feel (page 18 of the booklet).
- Source
- Hobie Class Association of North America (Boyd Bass & Bob Mimlitch), Hobie U, 31 Mar 2002
Base setup
- Rig tension
- Firm, but loose enough for the mast to rotate freely
- Mast rake
- Maximum rake while keeping enough leech tension; in moderate air reduce rake if you're block-to-block and the main still isn't powered up
- Rudders
- Parallel, no toe in or out
- Trampoline
- Tight
- Battens
- Just snug; release when not sailing
Upwind
| Control | Light air | Moderate air | Heavy air |
|---|---|---|---|
| Downhaul | Just smooth (set with the main sheeted normally) | Tight | Very tight, tighter still if the hull flies too high |
| Outhaul | Just taut | Just taut | Tight, flat sail |
| Traveller | Centred | Centred | Centred; up to 6" out if the hull keeps flying too high |
| Mainsheet | Medium, don't over-sheet; in as it builds | Tight | Play it to keep the windward hull skimming |
| Steering | Leeward telltale below the H flowing, on the verge of stalling | Same | Head up in gusts |
| Weight | Bows down, skipper on the crossbar or hull | Skipper on the windward hull, boat level | Skipper on the windward hull, boat level |
Downwind
| Control | Light–moderate | Moderate–heavy |
|---|---|---|
| Downhaul | Eased | Eased |
| Outhaul | Just taut | Bottom batten 4–6" draft |
| Traveller | ¾ to all the way out | ¾ to all the way out |
| Mainsheet | Light, in during gusts | Medium, in during gusts |
| Steering | Bridle fly at or slightly aft of 90° | Leeward telltale occasionally stalling; deeper in gusts |
Trim by condition
- Leech tension
- Keep a loose leech in light and heavy air; power the main up with more sheet in moderate air.
- From the NAHCA's 2002 Hobie University booklet. The class's newer 2010 Hobie 14 guide (Schafer/Curry) on hobieclass.com couldn't be opened because of a bot check.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Hobie 14 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Hobie 14 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Hobie 14 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesIHCA 2025-2028 Class Rules, revised 1 March 2026
- Class associationhobieclass.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Hobie 14 part