One-design race shop · Multihull
Hobie 16 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Hobie 16
All Hobie 16 equipment
12 parts
Fit verified for Hobie 16
Harken
Harken Cam Cleat - Cam-Matic 150 - Line: 1/8 to 1/2 in (3 to 12 mm)
Part # HAR150
$44.95
$50.80Fit verified for Hobie 16
Harken
Harken Block - Carbo 57mm Triple - Ratchet - Swivel / 150 Cam-Matic (Black)
Part # HAR2140
$284.95
$323.25Fit verified for Hobie 16
Harken
Harken Block - Carbo 40mm Triple - Swivel
Part # HAR2640
$143.95
$163.20Fit verified for Hobie 16
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Hobie 16
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Hobie 16
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66
No Hobie 16 parts match these filters.
Can’t find a part for your Hobie 16? Request a Hobie 16 part
Official Harken dealer
Hobie 16 deck layout
- Length
- 16 ft 7 in (5 m)
- Beam
- 7 ft 11 in (2.1 m)
- Mast
- 26 ft 6 in (8 m)
- Sail Area
- 218 sq. ft (20.25 sq. m)
- Weight
- 320 lb (145 kg)
Downhaul
-
1
22mm Cheek BlockHarken 233
$19.95 -
2
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
3
29mm Triple Block — SwivelHarken 344
$70.95 -
7
29mm Cheek BlockHarken 350
$18.95 -
8
40mm Triple Block — SwivelHarken 2640
$143.95
Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.
Go fast
Hobie 16 tuning guide
On the Hobie 16, rig tension and rake are set with the jib halyard and the shroud adjuster holes, and rake is measured with the main halyard from the bow to the stern of one hull. Most guides start at about 12–16" of rake and then work through downhaul, traveller and jib car by how hard you're hiking or trapezing. No gauge is used. Gavin Colby's well-known guide sits on the Hobie class site behind a bot check, so it isn't included here.
TheBeachcats.com — Modern Tips for Sailing the Hobie 16 Catamaran (speed matrix) Posted 24 Feb 2025 by Damon (the author, who sails with crew Liza, cites their 2003 Continentals result)
- Written for
- Standard Hobie 16 main and jib
- Tension gauge
- None
- How it’s measured
- Rake (class method): take the main halyard to one bow, hold it on top of the bridle screw and mark it; walk it back to the transom of the same hull and mark where it meets the bottom corner of the transom; the distance between the marks is the rake.
- Source
- TheBeachcats.com, Posted 24 Feb 2025 by Damon (the author, who sails with crew Liza, cites their 2003 Continentals result)
Base setup
- Mast rake
- 16" to start; the author never sets the mast further forward (more upright) than this. Adding rake in light air to reach block-to-block is a gamble that usually doesn't pay.
- Shrouds
- Bottom hole
- Jib tack
- Middle of the adjuster plate
- Rudders
- 1/8" toe-in
- Crew weight
- Class minimum 285 lb combined; about 300 lb is better across conditions
Speed matrix by mode
| Mode | Rake | Mainsheet | Traveller | Jib sheet | Jib car | Downhaul |
|---|---|---|---|---|---|---|
| No trapezing | 16" | 1 ft from block-to-block | Centre | Open slot | Inboard | Wrinkles out |
| Single trapeze | 16" | Almost block-to-block | Centre | Tight | Inboard | Wrinkles out |
| Just double trapezing | 16" | Block-to-block | Centre | Tight | Inboard | A bit more |
| De-powering 1 | 16" | Block-to-block | Down 6" | Tight | Out 2" | More on |
| De-powering 2 | Back 2" at the mast mark | Block-to-block | Down 6" | Tight | Out 3–4" | Hard |
| De-powering 3 | Back 2" more | Block-to-block | Down 12" | Easing | Out 6" | To the black band |
| Survival | Back 2" more | Block-to-block | At the leeward hiking strap | Eased | Halfway out | To the black band |
Trim by condition
- Waves
- Open the jib slot a little more.
- Heavy air
- Use the traveller first to depower; keep crew forward through tacks. The author's minimum-weight team struggles above about 20 kn.
- Downwind
- Keep the bridle wind indicator at about 90°.
- A sailor's own notes, not a sailmaker or class guide. The matrix's column headers are separated from the rows on the page; values are matched by position, and "Our 3–4"" in the source is read as "Out 3–4"".
Hobie Class Association of North America (Wally Myers) — Hobie 16 – Rigging and Tuning Guide (Hobie University) Hobie U, 31 Mar 2002
- Written for
- Standard Hobie 16 main and jib
- Tension gauge
- None
- How it’s measured
- Rake: release the downhaul and centre the mast, take the main halyard forward to the lip just in front of the bridle bolt and mark it, then to the heel of the same hull just below the drain plug and mark it; the gap between the marks is the rake. Also roughly 12–14" between boom and rear crossbar at full sheet.
- Source
- Hobie Class Association of North America (Wally Myers), Hobie U, 31 Mar 2002
Base setup
- Rig tension
- Set with the jib halyard: pull until the shrouds are snug, not super tight. Ease slightly in light and heavy air; more halyard tension in moderate 8–15 (units not stated). Heavier teams more tension. Mark the halyard so you can return to the start.
- Mast rake
- Maximum rake at which you can still sheet the main tight; 8–18" works, aim for 12" with shrouds just snug. Lighter teams and newer boats can carry more.
- Changing rake
- More rake: ease the jib halyard. Less: go up on the shroud adjusters and tighten the jib halyard. Never let the forestay go tight.
- Rudders
- 1/8–1/4" toe-in
- Trampoline
- Tight
- Battens
- Snug enough to remove wrinkles and give slight shape; more in lumpy conditions
- Telltales
- Jib 9–12" aft of the luff, main 12" aft of the boltrope; three sets per sail
Upwind
| Control | Light air | Moderate air | Heavy air |
|---|---|---|---|
| Downhaul | Remove horizontal wrinkles when sheeted | Tight | Very tight |
| Outhaul | Snug | Tight | Very tight |
| Main traveller | Centre to 6" out | Centre to 8" out | 8–12" out; if past halfway, loosen the jib halyard and reset to 8" |
| Mainsheet | Just snug; not block-to-block unless the jib halyard is eased | Almost block-to-block unless the halyard is eased | All the way in; feather or ease in gusts |
| Jib luff | Remove wrinkles | Just light | Tight |
| Jib traveller | Inboard to 4" out | Inboard to 8" out | Halfway to ⅔ out, no more |
| Jib sheet | Snug, not tight | Tight (ease for chop) | Very tight |
| Jib clew plate | 1–2 holes down | Middle to 1 hole down | 1–2 holes down |
| Weight | Bows down, crew to leeward, both on the crossbar or hull | Level, both trapezing side by side as needed | Level, double trapeze; move aft in chop or waves |
Downwind
| Control | Light–moderate | Moderate–heavy |
|---|---|---|
| Downhaul | Moderate | Tight |
| Outhaul | Tight | Tight |
| Main traveller | Out | All the way out |
| Mainsheet | 18–28" between blocks (tighter if the rig is loose); in during gusts | Tight to 18" between blocks; play gusts |
| Jib | Sheet loose, crew may hold it out; traveller all the way out | Trim to match the main; traveller all the way out |
| Steering | 90° or aft on the bridle fly; lower in gusts | Bridle fly at 90°; lower in big gusts |
| Weight | Forward, crew to leeward; try kicking up the windward rudder | Both to windward, boat level |
Trim by condition
- Depowering
- Downhaul and outhaul to maximum, then traveller out; don't ease the sheet a long way, which twists the main off and makes the boat hard to control. In very strong wind centre the traveller before gybing.
- Priorities
- The jib halyard is the most important adjustment; keep the leeward telltales flowing and don't pinch.
- From the NAHCA's 2002 Hobie University booklet (pages 19–20). The wind band "modest (8–15)" has no units.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Hobie 16 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Hobie 16 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Hobie 16 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesIHCA Rule Book dated 2026-01-03 (file R_Book_01032026; general rules + per-class rules incl. Hobie 16) - edition text not read directly
- Class associationhobieclass.com
- Builder specificationsHobie 16 on hobie.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Hobie 16 part