One-design race shop · Dinghy
Laser 2 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Laser 2
All Laser 2 equipment
13 parts
Fit verified for Laser 2
Davis Instruments
Davis Black Max Wind Direction Indicator
Part # dav-1295
$69.99
Fit verified for Laser 2
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Laser 2
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Laser 2
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66
No Laser 2 parts match these filters.
Can’t find a part for your Laser 2? Request a Laser 2 part
Go fast
Laser 2 tuning guide
The Laser 2 is a strict one-design two-person trapeze and spinnaker dinghy (Frank Bethwaite / Ian Bruce, 1978; about 8,200 built by Performance Sailcraft and Vanguard, long out of production). Class rules fix the rig, so tuning is limited to mast rake set via the jib halyard before racing (rule 6b forbids altering rake while racing), diamond tension and sail controls. The only published class guide is the UK Laser II Class Association's one-page 'Tips on Twos' sheet; the association's scanned Rigging Manual is an assembly manual and the association proposed winding itself up in October 2021. No sailmaker tuning guide was found.
UK Laser II Class Association — Tips on Twos (misc info gained over the years…) Undated class web tip sheet (QuickWebTips2.pdf)
- Written for
- Standard class main, jib and symmetric spinnaker (one-design)
- Tension gauge
- None; rake by tape measure, diamond tension by eye/feel
- How it’s measured
- Mast rake: attach a tape to the main halyard, pull it up to max, and measure to the top of the rudder gudgeon plate, with some jib (halyard) tension on — too much tension inverts the mast.
- Source
- UK Laser II Class Association, Undated class web tip sheet (QuickWebTips2.pdf)
Base setup
- Mast rake, normal / strong winds
- ~6.27 m (20 ft 7 in) halyard-to-top-of-rudder-gudgeon-plate
- Mast rake, light winds
- ~6.38 m (20 ft 11 in)
- Mast diamond tension
- Heavier crews use more tension; make sure the mast is straight side-to-side
- Main and jib sheets
- ~7 m braided rope each
- Spinnaker sheet
- 11 m of 8 mm (or less) Dyneema
Trim by condition
- Upwind
- Adjust traveller height so that, with the boom on the centreline, the top-batten tell-tale is breaking 50% of the time. Don't use the kicker upwind until overpowered, then use lots (and downhaul); once overpowered, play the mainsheet continually to keep the boat flat. Don't sheet the jib too tight (fairleads always at the furthest-in position) — look at the slot, then mark the sheets with a 'tightest' setting.
- Reaching
- Ease the outhaul from the (relatively) tight upwind setting; the kicker controls power in the mainsail — be prepared to dump the main in gusts.
- Gybing
- Pull the spinnaker round to windward as you go into the gybe; change the pole on a run (if windy), then get back onto a reach.
- Running
- Spinnaker pole square to the wind is fast, further forward can be more stable; ease the kicker to give more projected area.
- Sheet is a single page of bullet points; the two rake figures are the only numeric settings. The sheet's own wording is 'Rule #1: you are a team — work like one and talk to each other!'
- Class rule 6b: the mast rake shall not be altered by adjusting the jib halyard and/or standing rigging while racing, so set rake ashore for the expected wind.
- The association also hosts a scanned Laser 2 UK Rigging Manual (16 pages, image-only, no tuning numbers) and a Rigging DVD on YouTube; the PDF has no edition or date.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-04). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Laser 2 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Laser 2 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Laser 2 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesLaser II International Class Association Rules, in force from 1 March 2001 (PDF last modified 2012-08-20)
- Class associationlaser2sailing.org.uk
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Laser 2 part