One-design race shop · Dinghy
Naples Sabot Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Naples Sabot
All Naples Sabot equipment
29 parts
Fit verified for Naples Sabot
Harken
Harken Cam Cleat - Cam-Matic (Micro) 468 - Line: 5/64 to 1/4 in (2 to 6 mm)
Part # HAR468
$36.95
$41.50Fit verified for Naples Sabot
Harken
Harken Block - Micro 22mm Single - Cheek
Part # HAR233
$19.95
$23.05Fit verified for Naples Sabot
Harken
Harken Block - 57mm Ratchet Block - Swivel (Black)
Part # HAR2135
$86.95
$98.25Fit verified for Naples Sabot
Sea-Dog
Sea-Dog Double Braided Nylon Dock Line - 3/8" x 10' - White
Part # SDG-302110010WH-1
$9.67
$12.50Fit verified for Naples Sabot
Buccaneer
Buccaneer Twisted Nylon Dock Line with eye - 3/8", 10' long
Part # buc-cro-ndl3810
$6.52
Fit verified for Naples Sabot
Sea-Dog
Sea-Dog Double Braided Nylon Dock Line - 3/8" x 10' - Black
Part # SDG-302110010BK-1
$9.88
$12.80Fit verified for Naples Sabot
Taylor Made
Taylor Made Dock Line-Brd Wh 3/8X15
Part # TAY-2020108468
$7.42
$11.95Fit verified for Naples Sabot
Taylor Made
Taylor Made Dock Line-Brd Bl 3/8X15
Part # TAY-2020108464
$7.42
$11.95Fit verified for Naples Sabot
Buccaneer
Buccaneer Double Braid Dock Line with eye - 3/8", Blue, 15' long
Part # buc-cro-30-21115
$16.14
Fit verified for Naples Sabot
Sea-Dog
Sea-Dog Double Braided Nylon Dock Line - 3/8" x 20' - Black
Part # SDG-302110020BK-1
$16.25
$21.05Fit verified for Naples Sabot
Taylor Made
Taylor Made Dock Line-Brd Bk 3/8X25
Part # TAY-2020108461
$10.85
$15.95Fit verified for Naples Sabot
Buccaneer
Buccaneer Double Braid Dock Line with eye - 3/8", Blue, 25' long
Part # buc-cro-30-21125
$22.18
Fit verified for Naples Sabot
Sea-Dog
Sea-Dog Double Braided Nylon Dock Line - 3/8" x 20' - White
Part # SDG-302110020WH-1
$16.02
$20.75Fit verified for Naples Sabot
Buccaneer
Buccaneer Double Braid Dock Line with eye - 3/8", Black, 15' long
Part # buc-cro-30-24415
$16.14
Fit verified for Naples Sabot
Taylor Made
Taylor Made Dock Line-Brd Bl 3/8X25
Part # TAY-2020108465
$10.85
$15.95Fit verified for Naples Sabot
Buccaneer
Buccaneer Double Braid Dock Line with eye - 3/8", Black, 20' long
Part # buc-cro-30-24420
$19.10
Fit verified for Naples Sabot
Buccaneer
Buccaneer Twisted Nylon Dock Line with eye - 3/8", 15' long
Part # buc-cro-ndl3815
$8.40
Fit verified for Naples Sabot
Taylor Made
Taylor Made Dock Line-Brd Wh 3/8X25
Part # TAY-2020108469
$10.85
$15.95Fit verified for Naples Sabot
Sea-Dog
Sea-Dog Double Braided Nylon Dock Line - 3/8" x 15' - Black
Part # SDG-302110015BK-1
$12.92
$16.75Fit verified for Naples Sabot
Buccaneer
Buccaneer Twisted Nylon Dock Line with eye - 3/8", 20' long
Part # buc-cro-ndl3820
$10.60
Fit verified for Naples Sabot
Taylor Made
Taylor Made Dock Line-Brd Bk 3/8X15
Part # TAY-2020108460
$7.42
$11.95Fit verified for Naples Sabot
Buccaneer
Buccaneer Double Braid Dock Line with eye - 3/8", Black, 25' long
Part # buc-cro-30-24425
$22.18
Fit verified for Naples Sabot
Buccaneer
Buccaneer Twisted Nylon Dock Line with eye - 3/8", 25' long
Part # buc-cro-ndl3825
$13.18
Fit verified for Naples Sabot
Buccaneer
Buccaneer Double Braid Dock Line with eye - 3/8", Blue, 20' long
Part # buc-cro-30-21120
$19.10
Fit verified for Naples Sabot
Lalizas
Lalizas Cabo Floating Rope Diam. 20/64'' (8Mm), L 98,43Ft (30M), Orange
Part # LAL-70260
$12.46
No Naples Sabot parts match these filters.
Can’t find a part for your Naples Sabot? Request a Naples Sabot part
Official Harken dealer
Naples Sabot deck layout
- LOA
- 2.44 m, 8'10"
- Beam
- 1.17 m, 3'10"
- Approx Weight
- 31 kg, 68 lb
- Rated Sail Area
- 3.53 m², 38 sq. ft
- Mast Length
- 4.17 m, 13'8"
Vang
-
3
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
4
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
6
Micro Cam-Matic® CleatHarken 468
$36.95 -
7
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
8
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
9
18mm Fly Soft-Attach BlockHarken 2698
$25.95 -
10
18mm Fly Soft-Attach BlockHarken 2698
$25.95 -
11
18mm Fly Soft-Attach BlockHarken 2698
$25.95 -
12
22mm Cheek BlockHarken 233
$19.95 -
13
16mm Cheek BlockHarken 416
$20.95 -
14
16mm Block — SwivelHarken 417
$31.95 -
15
18mm Fly Soft-Attach BlockHarken 2698
$25.95 -
17
57mm Ratchet Block — SwivelHarken 2135
$86.95
Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.
Go fast
Naples Sabot tuning guide
The Naples Sabot is a cat-rigged leeboard pram, so tuning means mast rake (set ashore with mast blocks), outhaul, downhaul, vang, mainsheet/traveller and leeboard angle. Rake is described differently in each guide: North gives a masthead-to-transom length, while Quantum and Ullman use the height of the trimmed boom above the transom.
North Sails — Sabot Tuning Guide Undated web page
- Written for
- North Sabot mainsail (Proctor, LeFiel and Gold Finger masts mentioned as equivalent)
- Tension gauge
- None (unstayed rig)
- How it’s measured
- Rake: tape fixed to the top of the mast, measured to the top centre of the transom. Rake can only be changed ashore.
- Source
- North Sails, Undated web page
Base setup
- Mast rake
- About 13'3 3/4"
- On-the-water check
- Fully sheeted, the boom about 16" above the transom corner
- Leeboard
- Thin and wide below the waterline; about 3/4" thick
Upwind
| Control | Light (0–7 kn) | Medium (8–13 kn) | Heavy (14+ kn) |
|---|---|---|---|
| Outhaul | 6" from boom | 4", just showing creases in foot | 2", tight, always showing crease in foot |
| Downhaul | None | 1/2 of the wrinkles out | No wrinkles |
| Mainsheet | All telltales flowing | Top telltales just stalling 30% | All top telltales flowing |
| Leeboard | Raked slightly forward | Straight | If too much helm, rake slightly aft |
| Vang | None | None | Just snug, maybe vang sheeting |
Downwind
| Control | Light (0–7 kn) | Medium (8–13 kn) | Heavy (14+ kn) |
|---|---|---|---|
| Outhaul | Eased | 10–8" from the boom | 6" from the boom |
| Downhaul | None | None | None |
| Mainsheet | Eased to 90° | Eased to 90° | Pulled in to 80° |
| Leeboard | Pulled up | Pulled up | Pulled up |
| Vang | Top batten just twisting off | Tight, top batten parallel | Tighter, top batten parallel |
Trim by condition
- Rake
- Trouble pointing or holding a lane suggests too much rake; pointing well but slow suggests too little. Differences are an inch or two.
- Leeboard
- Raked slightly forward up to about 10 kn, more upright at 10–14 kn, slightly aft if heavy helm persists in more wind.
- Mainsheet
- Don't over-trim in light air. In heavy air sheet hard but never past the boat's corner; in puffs ease only 3–6" and anticipate them.
- Heel
- Upwind on starboard sail as flat as possible; a slight heel is fine on port.
- Crew position
- Sit as close to the thwart as possible so the bow doesn't dig and the stern doesn't drag.
- Downwind
- Ease all controls; boom never past 90°; above about 14 kn pull the boom in a little for stability. Lifting the leeboard is optional and limits manoeuvring.
- The text gives a 13+ kn heavy band while the table heads it 14+ kn.
Quantum Sails — Quantum Sails Sabot Tuning Guide 2015 (PDF dated September 2015)
- Written for
- Quantum Sabot mainsail (open-leech design)
- Tension gauge
- None (unstayed rig)
- How it’s measured
- Rake set ashore with blocks behind the mast; judged by the height of the trimmed boom above the transom.
- Source
- Quantum Sails, 2015 (PDF dated September 2015)
Base setup
- Upwind rake target
- Mast raked aft so the boom trims about 12"–18" above the transom; in light air you may need more rake (more blocks behind the mast) so the boom isn't too high
- Mast-step slop
- Use the maximum allowed, 1/4", so the mast can rock forward downwind
- Mainsheet system
- Stern traveller recommended; use a ratchet block
Trim by condition
- Downhaul
- Light: little or none (some horizontal wrinkles are fine). Medium: just remove the wrinkles. Heavy: tighter to pull the draft forward and open the leech. Too loose beats too tight if you can't adjust it often.
- Outhaul
- Upwind the foot sits 2"–5" off the boom (looser for heavier skippers), checked by sliding a hand between boom and sail aft of the mid mainsheet blocks; a little tighter in heavy air. Ease slightly off the wind.
- Vang
- Slack upwind. Reaching: enough for the top batten parallel to the boom. Running: top batten parallel or slightly twisted off.
- Traveller and mainsheet
- Traveller centred in light air, eased as the wind builds to control twist (watch the top-batten telltale). Boom just inside the transom corner about 90% of the time.
- Leeboard
- Straight down in most conditions; try it just forward of vertical in light air. Leave it down reaching, raise it out of the water running.
- Running
- Boom at right angles to the boat; mark the sheet at the cleat or tie a stopper knot.
- Body position
- Against the back of the thwart; slide aft in heavy air downwind.
Ullman Sails — Naples Sabot Racing Guide 2008 (PDF dated April 2008)
- Written for
- Not stated (Ullman Sails racing guide for the Naples Sabot)
- Tension gauge
- None (unstayed rig)
- How it’s measured
- 'Mast rake' is measured from the transom to the middle of the boom. Outhaul: from the middle of the boom (centre of the mainsheet block) to the sail 4" above the foot. Boom position: from the transom centreline.
- Source
- Ullman Sails, 2008 (PDF dated April 2008)
Mast rake (transom to middle of boom)
| Wind (kn) | Measurement |
|---|---|
| 0–5 | 16" |
| 6–10 | 18" |
| 10–15 | 20" |
| 15+ | Depends on your weight and mast stiffness; very little rake |
Outhaul (boom to sail 4" above the foot)
| Wind (kn) | Length |
|---|---|
| 0–5 | 7" |
| 5–10 | 6" |
| 10–15 | 4"–5" |
| 15+ | 3" (nearly overlapped with boom) |
Downhaul
| Wind (kn) | Tension |
|---|---|
| 0–5 | None |
| 5–10 | In puffs, 1/2 of wrinkles out |
| 10–15 | 3/4 of wrinkles out |
| 15+ | All wrinkles out |
Upwind boom position (off the transom centreline; mid or aft traveller)
| Wind (kn) | Boom position |
|---|---|
| 0–5 | 8" off centreline |
| 5–10 | 10"–12" off centreline |
| 10–15 | 16"–18" off centreline |
| 15+ | Depending on skipper weight, off the transom corner to 2"–4" outboard of it |
Leeboard upwind
| Wind (kn) | Leeboard |
|---|---|
| 0–8 (light) | Rake slightly forward |
| 8–12 (medium) | Straight |
| 15+ | If too much weather helm, rake slightly aft |
Trim by condition
- Mainsheet upwind
- Don't over-strap in light air. Lighter skippers (70–110 lb) ease in puffs to get flat, then sheet and hike; adjustments are only 3"–6".
- Mainsheet downwind
- Boom out to 90° in 0–12 kn; over 15 kn and overpowered, only 80°.
- Vang, centre mainsheet
- Little needed upwind until about 10 kn when you ease in puffs; downwind enough to hold the leech with the top batten slightly twisted.
- Vang, aft mainsheet
- The upwind 'gas pedal': enough to hold the leech with the upper third twisted off 10–15° in light-medium air, played in puffs; downwind a firm leech with slight twist. Don't over-tension.
- Leeboard downwind
- Pull it up, or at least rake it aft to 45°.
- Body position
- Light air lean forward on the thwart; move aft as the wind builds (smaller sailors 2"–3" aft of the thwart, up to 4" aft above about 12 kn). Up to 5° more heel is fine on port.
- The 'mast rake' figure here is a boom height above the transom, not a masthead-to-transom length, so it can't be compared with North's 13'3 3/4".
- The PDF's metadata title reads 'Melges 24 Tuning Guide', a leftover from Ullman's template; the content is the Naples Sabot guide. The link is a copy on canadianboating.ca.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Naples Sabot resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Naples Sabot by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Naples Sabot class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesINSA Class Rules, Revised January 1, 2026 (page also carries By-Laws revised January 1, 2025 and Yacht Specifications revised May 1, 2008)
- Class associationnaples-sabot.org
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Naples Sabot part