One-design race shop · Keelboat

Ensign Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Ensign

  • 41 verified parts
  • 2 brands
  • Fit checked Nov 2026

Fit verified for Ensign

All Ensign equipment

41 parts

Can’t find a part for your Ensign? Request a Ensign part

Official Harken dealer

Ensign deck layout

LOA
22 ft 6 in (6.8 m)
LWL
16 ft 9 in (5 m)
Beam
7 ft (2.1 m)
Hull Weight
3,000 lb (1360.5 kg)
Sail Area
255 sq. ft (23.6 sq. m)

Mainsheet

Mainsheet — Harken layout for the Ensign
Drawing: Harken
  1. 1 57mm Fiddle Block — Swivel, BecketHarken 2622 $73.95
  2. 2 57mm Fiddle Block — SwivelHarken 2621 $66.95
  3. 3 40mm Block — SwivelHarken 2636 $38.95
  4. 4 22mm Slider Car — Pinstop, EyestrapHarken 2750 $123.95
  5. 6 40mm Pivoting Lead Block — Cam-Matic® cleatHarken 2156 $89.95
  6. 7 38mm Wire BlockHarken 304 $77.95
  7. 8 29mm Triple Block — SwivelHarken 344 $70.95
  8. 9 29mm BlockHarken 348 $17.95
  9. 10 29mm Pivoting Lead Block — Carbo-Cam® cleatHarken 396 $72.95

Mainsheet Traveler

Mainsheet Traveler — Harken layout for the Ensign
Drawing: Harken
  1. 2 29mm Cheek BlockHarken 350 $18.95
  2. 4 29mm In-Line Exit Bullet BlockHarken 089 $46.95
  3. 6 22mm Small Boat CB Car — Pivoting Shackle, Control TangsHarken 2754 $236.95

Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.

Go fast

Ensign tuning guide

Ensigns are set up with the headstay near the class maximum, mast butt moved until there is about 1.5–2″ of prebend, then uppers, forward and aft lowers set by wind and backstay used to hit a target headstay reading. Quantum's current chart gives both Loos 91 Model A and PT-1 numbers; the older Quantum charts are Model A only and North's archived page doesn't name the Loos model, so check which gauge a number belongs to.

Quantum Sails — Ensign Tuning Guide Current PDF (file dated July 2026)

Written for
Quantum Ensign main, genoa and spinnaker (no model names)
Tension gauge
Loos Gauge 91 Model A and Loos PT-1, both shown (5/32″ stays)
How it’s measured
Forestay and backstay figures are gauge readings on those stays. Mast centred by hand-tightening uppers and forward lowers and measuring side to side with a halyard. Butt position cross-check uses pin-to-pin distances (see base).
Source
Quantum Sails, Current PDF (file dated July 2026)

Base setup

Headstay
Close to the class maximum of 26′ 3 3/4″; best all-purpose length 26′3″
Prebend target
1.5″ with uppers and forward lowers at about 38/35 units, rig centred, backstay hooked up reading 0–5 on the gauge (gauge on the forestay; or below 0 on the backstay if you have a furling foil with no wire to reach)
Mast butt
No fixed position because steps and partners vary; move the butt and shim at the partners (forward or aft) until the 1.5″ prebend appears
A1 / A2: forestay pin to upper (side) stay pin
8.2′ / 8.2′
B1 / B2: upper stay pin to backstay pin
14.25′ / 14.35′
C: backstay pin to aft face of mast at deck
14.03′
D: backstay pin to aft face of mast at butt
14.30′

Trim & tuning chart (Loos 91 Model A // PT-1)

Wind (kn)0–66–1210–1515+
Fore lowers35 // 2535 // 2538 // 2940 // 31
Upper shrouds36 // 2838 // 2940 // 3142 // 33
Aft lowers24 // 1924 // 1927 // 2027 // 20
Forestay5–10 // 5–815–25 // 12–1930–35 // 22–2740 // 31
Backstay0 // 00–12 // 0–820–25 // 17–1930 // 22
Outhaul1″ easedTightTightMax
Main vangNone/snugSnugMediumHeavy
Main leech10° openParallelParallel to 10° closedParallel to 10° closed
Main cunninghamNoneSlight wrinklesSmoothSmooth
Headstay26′ 3″SameSameSame
Halyard tensionLooseLoose/modModerateHeavy
Genoa carForward ½″CentreBack ½–1″Back 2″
Luff telltalesEven breakEven breakEven to top firstTop first always

Trim by condition

Gear changes
In lulls move main and genoa back to the lighter-wind settings; in puffs trim for speed. Overpowered: drop the traveller to flatten and ease weather helm, and move the genoa car back a little. Quantum says playing the backstay through wind changes is where the biggest gains are.
Main
Bring the top batten a few degrees to windward to point about 3–4° higher; when the boat slows go back to speed mode by easing the sheet and pulling the traveller up so the boom stays on centreline.
Genoa
Set leads for the prevailing breeze and play the sheet. Light air: about 3″ off the spreader and just touching the shrouds at the foot; as wind builds pull the foot in tighter with the leech still 2–3″ off the spreader, and move the car aft to twist and depower.
Genoa halyard
Looser than you think: scallops or speed wrinkles at the hanks, even droop between hanks in light air; keep the draft about 35–40% aft. Re-adjust the halyard whenever the backstay changes.
Backstay
Loose (extra headstay sag) pre-start for speed, then standard settings and a point/VMG mode after the start; more in puffs, less in lulls.
Crew
Forward and to leeward in light air; onto the benches from about 7 kn.
Downwind
Vang so the top batten is parallel to the boom. Pole just aft of square in light-medium and medium-heavy; square (90°) in light air; just forward of square in drifting conditions. Clews about even, guy 2–3″ higher; almost a curl in the windward shoulder. Pull the pole down when reaching hard. Slight windward heel when running in moderate air, flat to slightly leeward in light air; steer with crew weight from the middle/forward of the companionway.
  • The PDF's text layer carries a second, plain copy of the chart with the same numbers as the designed chart shown on the page.
  • B1 reads 14.25′ here but 14.35′ in Quantum's older diagram.
  • The halyard-tension row is a feel guide; Quantum says sail shape is the real gauge.

Quantum Sails — Ensign Tuning Guide (8-2018) August 2018 (file name 8-2018; PDF created 2 Aug 2018); contacts Doug Burtner and Randy Shore

Written for
Quantum Ensign main, genoa and spinnaker
Tension gauge
Loos Gauge 91 Model A (not B); 5/32″ stays
How it’s measured
Forestay and backstay rows are gauge readings on those stays. Prebend sighted up the mast.
Source
Quantum Sails, August 2018 (file name 8-2018; PDF created 2 Aug 2018); contacts Doug Burtner and Randy Shore

Base setup

Headstay
Close to class maximum 26′ 3 3/4″; best all-purpose 26′3″
Prebend target
1 ½–2″ (aim for 2″) with uppers and forward lowers at about 40/40, rig centred and backstay hooked up reading 0–5 on the forestay gauge
Mast butt
Shim the mast forward at the deck if there is room; with under 2″ of prebend move the butt aft a little, with too much move it forward, then re-tension
Butt reference diagram
A1/A2 8.2′; B1/B2 14.35′; C 14.03′; D 14.30′ (same definitions as the current guide)

Trim & tuning chart (Loos 91 Model A)

Wind (kn)0–66–1210–1515+
Fore lowers38404040
Aft lowers24242727
Uppers40404244
Forestay5–1015–2530–3540
Backstay00–1220–2530
Outhaul1″ easedTightTightMax
Main vangNone/snugSnugMediumHeavy
Main leech10° openParallelParallel to 10° closedParallel to 10° closed
Main cunninghamNoneSlight wrinklesSmoothSmooth
Headstay26′ 3″SameSameSame
Genoa carForward ½″CentreBack ½–1″Back 2″
Luff telltalesEven breakEven breakEven to top firstTop first always

Trim by condition

Main
Top batten to parallel and then a few degrees to windward points the boat 3–6° higher; ease the sheet and raise the traveller (boom on centreline) to get back to speed. Ease the main hard to bear away at the windward mark or to duck.
Genoa
Light air about 3″ off the spreader and just touching the shrouds at the foot; foot in tighter and still 2–3″ off the spreader as it builds; car aft to twist and depower.
Spinnaker
Clews about even with the guy 2–3″ higher; best with a 4–6″ curl at the windward shoulder. Pole just aft of square in light-medium and medium-heavy, square in light air, just forward in drifters; pull it down when reaching hard.
Crew
Forward and to leeward in light air, to the benches from around 7 kn; heel to weather when running in moderate air.
  • The chart is an image; its Main leech cells show degree signs (10° open, parallel to 10° closed) that the PDF's text layer drops.
  • Reaching under genoa, this edition also says to let the main twist to match the genoa leech.
  • Shroud numbers are higher than the current chart's Model A column (e.g. uppers 40/40/42/44 vs 36/38/40/42).

Quantum Sails — Ensign Tuning Guide ('final') PDF created 20 July 2015 (Quantum Sail Design Group branding; four Quantum contacts listed)

Written for
Quantum Ensign main, genoa and spinnaker
Tension gauge
Loos Gauge 91 Model A (not B); 5/32″ stays
How it’s measured
As the 2018 edition; backstay and forestay share one row of gauge readings.
Source
Quantum Sails, PDF created 20 July 2015 (Quantum Sail Design Group branding; four Quantum contacts listed)

Base setup

Headstay
Close to class maximum 26′ 3 3/4″; best all-purpose 26′3″
Prebend target
1 ½–2″ with uppers and forward lowers at about 40/40 and backstay reading 0–5 on the forestay gauge
Butt reference diagram
A1/A2 8.2′; B1/B2 14.35′; C 14.03′; D 14.30′

Trim & tuning chart (Loos 91 Model A)

Wind (kn)0–66–1210–1515+
Fore lowers38404040
Aft lowers24242727
Uppers40404244
Backstay/forestay5–1515–303540
Outhaul1″ easedTightTightMax
Main vangNone/snugSnugMediumHeavy
Main leech10° openParallelParallel to 10° closedParallel to 10° closed
Main cunninghamNoneSlight wrinklesSmoothSmooth
Headstay26′ 3″SameSameSame
Genoa carForward ½″CentreBack ½–1″Back 2″
Luff telltalesEven breakEven breakEven to top firstTop first always

Trim by condition

Trim text
Same advice as the 2018 edition (top batten to windward points 3–6° higher; genoa 3″ off the spreader in light air, 2–3″ as it builds; spinnaker guy 2–3″ higher with a 4–6″ shoulder curl).
  • Edition order is from the PDF dates; the only chart difference from 2018 is a single combined 'Backstay/Forestay' row.
  • This edition says to sand the bottom to a 400 finish; the 2018 and current editions say 600.
  • As in 2018, the image chart shows degree signs on the Main leech cells that the text layer drops.

North Sails — Ensign Tuning Guide (North Sails One Design) Print of North's onedesign.com Ensign page dated 8/3/2015 (page footer © 2014 North Sails Group)

Written for
North main, genoa, #2 genoa, blade jib, spinnaker
Tension gauge
Loos gauge, model not stated (the page spells it "loose" gauge)
How it’s measured
Headstay tension read with the gauge on the forestay; mark a backstay scale (paint stirrer or ruler) at forestay readings of 20, 25, 35 and 40.
Source
North Sails, Print of North's onedesign.com Ensign page dated 8/3/2015 (page footer © 2014 North Sails Group)

Base setup

Headstay
26′ 21/4″ as printed (likely 26′ 2¼″)
Mast step
Adjust so the mast rests against the partners; chock it centred side to side and fore and aft
Uppers and forward lowers
40 with the backstay slack; gives about 1 ¼″ prebend
Aft lowers
24–26 with the backstay slack
On the water
At about 12 kn true with the headstay at 40 the leeward upper should just start to go slack; masts vary in stiffness, so adjust uppers or forward lowers to keep it in tune
Spreaders
Cut down to within 1″ of class minimum (printed "1:")
Genoa track
Drill holes every ½″

Headstay tension by true wind (gauge on the forestay)

True wind (kn)Headstay tension
0–30
3–65
6–1215
10–1525
15+40

Trim by condition

Main
Use the traveller (about 4–6″ of travel) to keep the boat flat in breeze, then the sheet; in light air pull the traveller up to windward so the boom is about 1″ to windward of centre (the page prints 'bottom'). In drifting conditions use sheet and traveller for lots of twist. Ignore the backwind bubble behind the mast; over-trimming the main to windward drives the boat sideways. Leech telltales and top batten are the stall indicators.
Genoa lead
Find the mid-range mark in about 12 kn true: the genoa touches the shroud at deck level and near the mast and telltales break evenly. Range is 1″ forward to 2″ back; in 0–5 kn go 1″ forward and keep the leech as close as ½″ to the spreader.
Headsail ranges
Genoa 0 to gusts of 20 kn true. #2 trims tight to the shrouds and is best when gusting high teens to low twenties; above a sustained 20 switch to the blade. Blade from a sustained 20 kn, even in big seas.
Blade
Tracks are too close to centreline, so never over-trim (ease when in doubt) and never pull the upper batten inside the upper shroud; set its mid-range mark in 12–15 kn; set telltales so the top breaks first; a 2:1 sheet if class rules allow.
Spinnaker
Standard trim, don't over-trim, correct pole height; the Ensign runs quite square, so don't gybe too high; tweakers help in lumpy seas; keep the chute dry when windy. Genoa under the spinnaker above 15 kn, jib in most conditions (drop before gybing).
General
Weight forward, boat flat for a neutral helm; minimum weight, low-stretch halyards, strong mast step.
  • Browser print of North's old onedesign.com Ensign page (URL tabid/25116 in the header, © 2014 North Sails Group in the footer), hosted on a third-party document server; North's current site has no Ensign guide.
  • The headstay table reads cleanly on the rendered page (tension 0/5/15/25/40 against 0–3/3–6/6–12/10–15/15+ kn true); only the PDF's raw text layer runs the two columns together.
  • The Loos model is not named, so don't assume these readings match either column of Quantum's chart.
  • North's 26′ 2¼″ headstay is shorter than Quantum's 26′ 3″.

Quantum Sails — Want to Sail Your Ensign Faster? Try These Tips. (Ensign clinic, Newport Regatta) July 1, 2015 (Doug Burtner)

Written for
Quantum Ensign sails
Tension gauge
Not stated
How it’s measured
Clinic notes; centre the rig with the genoa halyard, then tighten uppers and forward lowers with equal turns each side (no turn counts or tension figures).
Source
Quantum Sails, July 1, 2015 (Doug Burtner)

Trim by condition

Genoa power mode
At starts, after tacks and in chop the trimmer sets the genoa in power mode, about 6–8″ off the spreader tip, to build speed.
Heel downwind
Some windward heel can help downwind in light air; in anything above 8 kn keep the boat flat.
  • Article-style tips; use the Quantum tuning chart for the numbers.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Ensign resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Ensign by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current Ensign class rules before changing equipment, and ask your class measurer if a part is not original equipment.