Photo: Remi Jouan / Wikimedia Commons, CC BY-SA 3.0 (creativecommons.org/licenses/by-sa/3.0)
One-design race shop · Keelboat
Melges 24 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Melges 24
All Melges 24 equipment
64 parts
Fit verified for Melges 24
Harken
Harken Block - Classic Bullet 29mm Double - Upright
Part # HAR220
$53.95
$60.60Fit verified for Melges 24
Harken
Harken Block - Carbo 75mm Single - Ratchet Cheek (Black)
Part # HAR2672
$106.95
$121.55Fit verified for Melges 24
Harken
Harken Torlon Ball Bearings - Dia: 1/4 in (6.4 mm) - Balls: 21
Part # HAR177
$16.95
$18.70Fit verified for Melges 24
Harken
Harken Loop Soft Attachment - Dia: 1/8 in (3.0 mm) - Length: 6 1/2 in (165.0 mm)
Part # HAR2155
$15.95
$18.25Fit verified for Melges 24
Harken
Harken Block - Carbo Ratchamatic 75mm Single - Cheek - Standard Grip (Black)
Part # HAR2682
$171.95
$195.25Fit verified for Melges 24
Harken
Harken Block - Carbo Power3 Switchable 75mm Single - Swivel / Standard Grip (Black)
Part # HAR2670
$104.95
$118.90Fit verified for Melges 24
Harken
Harken Block - Wire High Strength 38mm - Wire - Through-Deck
Part # HAR306
$85.95
$97.05Fit verified for Melges 24
Premium Ropes
Anchor Line - 8 mm (5/16 in) Polyester 3-Strand, by Premium Ropes
Part # PRR-201-08-BLK
$0.49
$0.58Fit verified for Melges 24
Premium Ropes
Anchor Line - 10 mm (3/8 in) Polyester 3-Strand, by Premium Ropes
Part # PRR-201-10-BLK
$0.83
$0.98Fit verified for Melges 24
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 1/2" X 150' long
Part # buc-cro-nal12150
$122.00
$123.70Fit verified for Melges 24
Powerwinch
Powerwinch 150' of 1/2" Rope 10' of 1/4" HT Chain Rode
Part # pow-p10293
$381.00
$403.92Fit verified for Melges 24
Lewmar
Lewmar Rode - 10'1/4"G4 150'1/2"8P Skl/Swv
Part # LEWHM10HT150PXS
$279.00
$422.95Fit verified for Melges 24
Harken
Harken Cam Cleat - Carbo-Cam 365 (Standard) - Line: 1/8 to 3/8 in (3 to 10 mm)
Part # HAR365
$34.95
$40.10Fit verified for Melges 24
Lewmar
Lewmar Anchor Rode - 1/4 in Chain (10'), 1/2 in 8-Plait Nylon (200')
Part # LEWHM10HT200PX
$469.00
$735.95Fit verified for Melges 24
Lewmar
Lewmar Rode - 150' 1/2"8Plt Splcd 5/16" Skl
Part # LEWHM150PX
$329.00
$498.95Fit verified for Melges 24
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 1/2" X 200' long
Part # buc-cro-nal12200
$161.00
$169.04Fit verified for Melges 24
Lewmar
Lewmar Rode - 10' 1/4"G4 150"1/2"8Plt W/Shkl
Part # LEWHM10HT150PX
$382.00
$597.95Fit verified for Melges 24
Lewmar
Lewmar Rode - 8'1/4"G4 200'1/2"Rope W-5/16
Part # LEW69000333
$361.00
$545.95Fit verified for Melges 24
Lewmar
Lewmar Rode - 10'1/4"G4-200'1/2"8Pltw/Shkl&S
Part # LEWHM10HT200PXS
$493.00
$769.95Fit verified for Melges 24
Buccaneer
Buccaneer Twisted Nylon Anchor Lines - 3/8" X 150' long
Part # buc-cro-nal38150
$70.70
Fit verified for Melges 24
Lewmar
Lewmar Rode - 6' 1/4" G4 150' 1/2" 8 Plt Rop
Part # LEWHM06HT150P
$358.00
$561.95Fit verified for Melges 24
Lewmar
Lewmar Anchor Rode - 1/4 in Chain (10'), 1/2 in 3-Strand Polyster (150')
Part # LEW69000332
$289.00
$435.95Fit verified for Melges 24
Harken
Harken Block - Wire High Strength 38mm - Wire
Part # HAR304
$77.95
$88.95Fit verified for Melges 24
Harken
Harken Block - Carbo 29mm Single - Fixed Head
Part # HAR348
$17.95
$19.90Fit verified for Melges 24
Harken
Harken Cam Cleat - Cam-Matic 150 - Line: 1/8 to 1/2 in (3 to 12 mm)
Part # HAR150
$44.95
$50.80Fit verified for Melges 24
Harken
Harken Block - Carbo Power3 Switchable 75mm Single - Swivel / 2x Grip (Silver)
Part # HAR2176
$111.95
$127.25Fit verified for Melges 24
Harken
Harken Block - Carbo 40mm Single - Fixed Head
Part # HAR2650
$31.95
$35.75Fit verified for Melges 24
Vakaros
Vakaros Atlas Edge (High-Performance GPS Sailing Instrument)
Part # VAK-VK-EDGE
$749.00
$775.75Fit verified for Melges 24
Harken
Harken Block - Carbo 57mm Single - Swivel / Becket
Part # HAR2601
$62.95
$71.15Fit verified for Melges 24
Harken
Harken Block - Carbo 57mm Double - Swivel
Part # HAR2602
$118.95
$135.10Fit verified for Melges 24
Barton Marine
Barton Windicator WP285 – Offshore Racing
Part # bam-84004
$59.00
Fit verified for Melges 24
Davis Instruments
Davis Spare Vane f/WindTrak 10.Sport
Part # dav-3101
$29.99
Fit verified for Melges 24
Harken
Harken Swivel Cam Cleat - Base (Standard) w/ Cam-Matic 150 - Line: 1/8 to 1/2 in (3 to 12 mm)
Part # HAR144
$180.95
$205.65Fit verified for Melges 24
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Melges 24
Vakaros
Vakaros Atlas 2 (GPS, Compass)
Part # VAK-VK-ATLAS2
$1,249.00
$1,295.81Fit verified for Melges 24
Velocitek
Velocitek Mast Bracket for Prostart or SpeedPuck
Part # VELPROMMB
$69.00
Fit verified for Melges 24
Harken
Harken Block - 57mm Ratchet Block - Swivel (Black)
Part # HAR2135
$86.95
$98.25Fit verified for Melges 24
Davis Instruments
Davis Universal Masthead Mount f/WindTrak 10.Sport & WindTrak 15
Part # dav-1705
$59.99
Fit verified for Melges 24
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Melges 24
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for Melges 24
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95
No Melges 24 parts match these filters.
Can’t find a part for your Melges 24? Request a Melges 24 part
Official Harken dealer
Melges 24 deck layout
- Length
- 24 ft (7.82 m)
- Beam
- 8 ft 2 in (2.499 m)
- Draft
- 5 ft (1.52 m)
- Weight
- 1,783 lb (809 kg)
- Main
- 264 sq ft (21.0 sq m)
- Jib
- 126 sq ft (12.0 sq m)
- Spinnaker
- 670 sq ft (55.9 sq m)
Mainsheet
-
1
40mm T2™ Loop Soft-Attach BlockHarken 2148
$51.95 -
3
Standard Cam-Matic® Cleat - 150Harken 150
$44.95 -
4
57mm T2™ Soft-Attach BlockHarken 2152
$53.95 -
5
57mm T2™ Soft-Attach BlockHarken 2152
$53.95 -
6
57mm T2™ Loop Soft-Attach BlockHarken 2151
$60.95 -
7
75mm Cheek Ratchamatic® BlockHarken 2682
$171.95 -
8
75mm Cheek Ratchamatic® BlockHarken 2682
$171.95 -
9
38mm Wire BlockHarken 304
$77.95 -
10
Standard Cam Base — SwivelHarken 144
$180.95 -
12
57mm Double Block — SwivelHarken 2602
$118.95 -
14
40mm T2™ Loop Soft-Attach BlockHarken 2148
$51.95
Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.
Go fast
Melges 24 tuning guide
The Melges 24 is tuned from a fixed rake of 36′6½″ (11.140 m, masthead to the transom/hull-bottom corner) and a base upper-shroud tension, then wound up or down by counted turns as the wind changes; shrouds may be adjusted while racing. Turn counts depend on the turnbuckle type (North and Ullman count Ronstan turns, Quantum counts open-body turns), and the base reading is quoted on different gauges (North: 16 on a Loos Model B; Ullman: 20 Model B = 16 PT-2; Quantum: 15 on a PT-2), so stay inside one guide.
North Sails — Melges 24 Tuning Guide (with Melges 24 Speed Guide) Current web page (no revision shown)
- Written for
- North Melges 24 main, jib and asymmetric spinnakers (Speed Guide: 3Di main and jib, reacher and runner spinnakers)
- Tension gauge
- Loos Model B for the uppers; lowers set by sighting mast sag (with a Model B reading for the base)
- How it’s measured
- Rake: 50′ tape hoisted two-blocked on the main halyard (shackle removed), measured from the masthead to where the transom meets the bottom of the hull. Uppers at 16 when measuring. Centre the mast by measuring from the masthead to the chainplates, then to the deck at the upper-sidestay position, on each side.
- Source
- North Sails, Current web page (no revision shown)
Base setup
- Rake
- 36′6½″ (11.140 m), adjusted with the turnbuckle above the Hyfield lever, with uppers at 16 (Model B)
- Uppers (base)
- 16 on a Loos Model B, the 6–8 kn setting
- Lowers (base)
- Model B pulled to the line reads 68 mm from the shroud to the end of the gauge; in use about ¾″ leeward sag
- Pre-stretch
- Wind the uppers on 18 turns and the lowers 15 turns, check the mast is straight, then return the uppers to 16 and re-check centring and rake
- Spreader marks
- Dark tape 12″ (305 mm) in from each spreader tip, used to judge jib trim
- Jib lead (base)
- Third bolt head from the back of the jib track (drill extra holes either side of it)
- Turnbuckles
- Chart is written for Ronstan turnbuckles and the internal-wire jib halyard; on open-body turnbuckles use ½ turn for each full Ronstan turn
Shroud settings, standard (wire-halyard) forestay: turns from base on Ronstan turnbuckles (base uppers = 16 Model B)
| Wind (kn) | Uppers | Lowers |
|---|---|---|
| 0–6 (light) | Loosen 2 turns from base | ¾″ leeward sag, loosen 1 turn from base |
| 6–8 (base) | Loos 16 – base | ¾″ leeward sag – base |
| 7–10 | +3 | +2 |
| 10–11 | 6 | 4 |
| 11–12 | 9 | 6 |
| 12–13 | 12 | 8 |
| 13–15 | 15 | 11 |
| 15–17 | 18 | 14 |
| 17–19 | 20 | 17 |
| 19–21 | 23 | 20 |
| 21–23 | 25 | 24 |
| 23+ | Loosen forestay 5 turns, go to 29 | 27 |
Shroud settings, fixed forestay with Vectran jib halyard: turns from base (base uppers = 16 Model B)
| Wind (kn) | Uppers / forestay | Lowers |
|---|---|---|
| 0–6 (light) | Loosen 2 turns from base | ¾″ leeward sag, loosen 1 turn from base |
| 6–8 (base) | Loos 16 – base | ¾″ leeward sag – base |
| 7–10 | Loosen forestay turnbuckle 6 full turns from base; uppers +2 from base | +1.5 |
| 10–11 | 5 | 3.5 |
| 11–12 | 8 | 5.5 |
| 12–13 | Loosen forestay 12 full turns from base; uppers +10 from base | 7.5 |
| 13–15 | 12 | 9 |
| 15–18 | Loosen forestay 18 full turns from base; uppers +15 from base | 12 |
| 17–20 | 18 | 14 |
| 19–21 | 21 | 16 |
Trim by condition
- Lowers
- Set by sighting up the back of the mast; keep the middle from bending to windward. Only when the main inverts and flogs in puffs, tighten the lowers so the top falls off to leeward. With tight lowers always keep some backstay on downwind or the mast can invert and break.
- Sea state
- In waves err slightly tight on the shrouds (softer backstay, looser mainsheet); in flat water err light for more backstay and bend. Leave the dock at the light-medium base and set for the lightest wind expected on the first beat.
- Main sheet
- Light–moderate: top-batten telltale stalled about 25% of the time (second telltale always flying), top batten parallel to centreline; heavy air: top batten about 5° open.
- Backstay
- None upwind until about 12 kn true, then ease/trim the mainsheet with every backstay change; in puffy air play backstay rather than mainsheet; very windy, backstay hard and work the main.
- Outhaul
- Clew at the black band with crew on the rail; 1″ in when crew is in the boat; 2–3″ in downwind (tight when tight-reaching in breeze).
- Vang
- Snug once overpowered so easing sheet doesn't open the leech; harder to flatten the lower third. Downwind, top batten parallel to the boom; mark an approximate downwind setting.
- Cunningham
- Off below 16 kn (slight luff wrinkles); above 16 kn just enough to remove wrinkles; off downwind.
- Traveller
- Keep the car between the helmsman's foot rests. Light air at the windward foot rest; crew hiking: centred or above centreline in chop; very windy: centred or raised with a soft sheet.
- Jib
- ½″ of sheet makes a big difference. Lead one special hole forward of base in light air, aft of base above base conditions, up to 3 holes aft in heavy air (further forward in chop). Trim until the upper leech telltale is on the edge of stalling. Tack line set for slight luff wrinkles; smooth in very heavy air. Keep the leech cord loose.
- Spinnaker
- Tack down to the pole end on reaches; when it will ride straight up, ease the tack line 12–18″. Set and douse behind the shrouds; gybe inside (tack line over the sheet).
- Speed Guide (Brian Janney)
- Crew limit 825 lb (375 kg), usually five aboard. About 20 turns from base to 20 kn. About 75% backstay from 12 kn up; if you keep easing backstay, ease the shrouds, and if near maximum backstay, tighten them. In 12 kn the jib telltale can stall slightly; ease the jib ½″ as it gets windier. Boat begins to plane at about 14 kn. Keep at least 2.5 kn of speed on the starting line.
- The 7–10 kn row overlaps the 6–8 base band, and later rows give bare numbers; the guide reads them as cumulative turns on from base.
- The web page cuts off part-way through the spinnaker douse section.
- North recommends recording turnbuckle numbers (or measuring open-body stud gaps with a micrometer) at base so the setting can be repeated.
- The rake is printed as 36′6½″ (11.140 m); 36′6½″ converts to about 11.138 m.
- Speed Guide (Brian Janney, undated): https://northsails.com/sailing/en/resources/melges-24-speed-guide
Quantum Sails — Melges 24 Quick Tune (Dyform shrouds) 2026_v13
- Written for
- Quantum Melges 24 main and jib; AIRX650 spinnakers (Z1 AP runner 9–14 kn, V4 reacher 0–8 and 15+ kn)
- Tension gauge
- Loos PT-2
- How it’s measured
- Rake by hoisting a tape to the masthead on the main halyard, measured to the transom edge at the waterline. Turns are full turns from base on open-body turnbuckles; record caliper readings between the turnbuckle ends at base.
- Source
- Quantum Sails, 2026_v13
Base setup
- Rake
- 36′ 6½″
- Uppers
- 15 on PT-2
- Lowers
- 15 on PT-2, then 7 full turns off
- Base wind
- All turns are from base, the 5–6 kn setting
- Rig
- Black Southern Spars mast with Dyform upper and lower shrouds, open-body turnbuckles
- Jib lead numbering
- Holes numbered 0–5; hole #2 is the drilled-out 3rd bolt head from the back of the track; base lead (#1) for 5–6 kn is one hole forward of it
Quick Tune by true wind (turns from base; PT-2 base 15/15 −7)
| TWS (kn) | Uppers | Lowers | Mast sag | Jib lead | Jib cunn | Main cunn | Traveller (upwind) | Vang (upwind) | Backstay (upwind) | Jib furl (downwind) | Spinnaker (downwind) |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 0–4 | −1 | −2 | 25 mm | 0 | Ease | None | Max up | 0 | 0 | In | V4 |
| 5–6 | Base | Base | 20 mm | 0 | Ease | None | Max up | 0 | 0 | In | V4 |
| 7–9 | 3 | 2 | 15 mm | 1 | Some | None | Up 8" | Slack out | 0 | In | Z1/V4 |
| 9–12 | 6 | 4 | 10 mm | 1 | Some | 20% | Up 6" | 30% | 30% | In/Out | Z1 |
| 12–14 | 10 | 8 | 0 | 2 | Smooth | 40% | Up 6" | 50% | 40% | Out | Z1 |
| 15–18 | 14 | 12 | 0 | 2 or 3 | Smooth | 60% | Up 4" | 60% | 50% | Out | V4 |
| 19–20 | 16 | 14 | Poke | 3 | Smooth | 80% | Up 4" | 75% | 80% | Out | V4 |
| 21–24 | 18 | 16 | Poke | 4 | Smooth | Max | Up 2" | 75% | Max | Out | V4 |
| 25+ | 20 | 20 | Max poke | 4 | Smooth | Max | Up 2" | 75% | Max | Out | V4 |
Trim by condition
- Backstay
- Above 12 kn hook the backstay bridle around the motor mount to get maximum tension.
- Lowers in breeze
- Make sure the lowers are tight from 15 kn when overpowered so the headstay is properly tensioned and the main doesn't invert too early (clew-to-spreader area).
- Light-air race report (Quantum 'Podium Insights', Scott Nixon, July 2018)
- Quantum's team sailed at its base tune with 15 on the uppers (the article says PT1 gauge), lowers backed off 1.5 full turns for almost 1″ of sag at the spreaders with no backstay, jib lead in the third hole forward of the third screw head, traveller fully to windward, about 20/40/60% backstay with one/two/all crew hiking, target upwind speed around 5.3 kn.
- The chart shows jib lead 0 at the 5–6 kn base row, while its tips call the 5–6 kn base lead #1; check which hole numbering you use.
- The 'Podium Insights' article (https://www.quantumsails.com/en/resources-and-expertise/articles/podium-insights-a-detailed-review-of-how-melges-24) quotes the uppers on a PT1 gauge while the chart uses a PT-2, so treat that reading with care.
- Not for older boats with other masts or rod/wire shrouds; the chart says it is for the black Southern Spars mast with Dyform shrouds.
Ullman Sails — Melges 24 Tuning Guide, Tuning Chart and Sailing Guide Undated (file names on the host say 2014; PDF metadata dates the guides to 2009–10; Tickler: Version 5)
- Written for
- Ullman Melges 24 main, jib and asymmetric spinnaker
- Tension gauge
- Loos Model B with PT-2 equivalents in brackets (the chart quotes the base as 16 on a PT-2)
- How it’s measured
- Rake: main halyard tied to a 50′ tape, two-blocked, measured to the intersection of the hull and the bottom edge of the transom, with some rig tension on. Turns are full turns on Ronstan calibrated turnbuckles with the old forestay system. Jib lead measured from the centre of the jib-car pin to the back edge of the cabin coaming at deck level.
- Source
- Ullman Sails, Undated (file names on the host say 2014; PDF metadata dates the guides to 2009–10; Tickler: Version 5)
Base setup
- Rake
- 36′6½″; pull forward to 36′8″ in under 7 kn with crew in the boat (then loosen uppers 6 and lowers 3 turns to keep the same tension)
- Base wind
- 8–11 kn (the text also calls it 7–11 kn)
- Uppers (base)
- 20 on Model B (16 on PT-2)
- Lowers (base)
- Tighten to 18 Model B (15 PT-2), centre the middle of the mast by sighting, then loosen 15 turns; sailing upwind they should allow ½–1″ leeward sag between the black band and the hounds
- Shroud rule of thumb
- Turn the caps twice as much as the lowers until the main starts luffing, then bring the lowers up to match (e.g. 18 over 9, 18 over 18, then 21 over 21); change in 3-full-turn steps
Tuning chart by wind (full turns from base on Ronstan turnbuckles)
| Wind (kn) | 0–6 | 7 | 8–11 | 12–15 | 16–19 | 20+ |
|---|---|---|---|---|---|---|
| Mast rake | 36′8″ | 36′6.5″ | 36′6.5″ | 36′6.5″ | 36′6.5″ | 36′6.5″ |
| Uppers | −12 | −6 turns | 16 on Loos PT-2 (base) | +6–12 turns | +18–24 turns | 27 turns |
| Lowers | −6 | −3 turns | See tuning guide | +3–6 turns | +9–24 turns | 27 turns |
| Backstay | Loose | Loose | Loose | Medium | More | Max |
| Traveller (distance below centreline) | Centre boom | Centre boom | 0–6" | 0–1" | 1" above centre | 1" above centre |
| Outhaul (mid-foot from boom) | 2–3" | 2" | 1" | Tight | Tight | Tight |
| Upwind vang | Loose | Loose | Loose | Snug | Max tight | Slight ease |
| Jib lead (cabin to jib-car pin) | 206 mm | 206 mm | 184 mm | 162 mm | 162 mm | 155 mm |
| Jib luff tension | Wrinkles | Wrinkles | Wrinkles | Slight wrinkles | No wrinkles | Tight |
| Spinnaker tack line | Tight | Tight | Eased 1"–3" | Tight | Tight | Tight |
| Cunningham | Wrinkles | Wrinkles | Wrinkles | Wrinkles out | Tight | Tight |
Trim by condition
- Main sheet
- Light air: aft 2′ of the top batten parallel to the boom, or 5–10° open in light air and chop. Medium: sheet hard, top batten parallel. Overpowered: use the sheet to control twist.
- Backstay
- Loosest until overpowered at about 12 kn, then play it in puffs (ease the sheet when easing backstay). Hook the starboard backstay leg around the motor mount for more throw. Downwind: off in light–medium air; leave most of it on when planing.
- Traveller
- Boom on centreline until overpowered, then drop 2″ at a time, alternating with backstay. Heavy air and waves: car centred, max vang, play the sheet; in extreme conditions ease the vang and use the sheet.
- Vang
- Loose in light air; slack out as the sheet comes on; very hard when vang-sheeting. Light-air downwind top batten 10–15° open from the boom; in full planing sheet through the last upper mainsheet block and leave the vang loose.
- Outhaul
- Light air and chop: foot 1–2″ off the middle of the boom; otherwise tight upwind. Downwind 5″ in displacement mode, 7–8″ planing.
- Cunningham
- Light: wrinkles; medium: just removed; heavy: very firm. Off downwind.
- Jib
- Trim until the sewn leech telltale is about to stall (it may stall in very light air, chop, out of tacks and off the line). Leads 206 / 184 / 162 mm for light / medium / heavy. Luff: slight wrinkles light, slight to none medium, none to very tight heavy; leech line as loose as possible.
- Spinnaker
- Tack to the pole in light and heavy air; eased 1–2″ in medium (to the pole in very choppy water). Keep about 6″ of luff curl and never over-trim. Always gybe inside.
- Crew
- Flat upwind; weight forward to the shrouds in light air, from the shroud aft in medium, about 1′ further aft in heavy air.
- The tuning guide says base is 8–11 kn and also 7–11 kn, and quotes the uppers as 20 (16) while the chart names only the PT-2 reading of 16.
- Heavy-air lowers are a wide range (+9–24 turns); see the guide's rule of thumb for how to step them.
- Ullman no longer hosts these files; the links are copies on canadianboating.ca. Related copies: Sailing Guide (https://canadianboating.ca/wp-content/uploads/2020/05/Ullman-Sails-Melges-24-Racing-Guide-2014.pdf), Tuning Chart (https://canadianboating.ca/wp-content/uploads/2020/05/Ullman-Sails-Melges-24-Tuning-Chart-2014.pdf) and Erik Shampain's 'Tickle your Melges 24' boat-prep list V5 (https://canadianboating.ca/wp-content/uploads/2020/05/Ullman-Sails-Melges24-Tickle-V5.pdf).
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Melges 24 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Melges 24 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Melges 24 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesInternational Melges 24 Class Rules, effective date 2026-January-30 (Status: Approved)
- Class associationmelges24.com
- Builder specificationsMelges 24 on melges.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Melges 24 part