One-design race shop · Multihull
Dart 18 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Dart 18
All Dart 18 equipment
2 parts
Fit verified for Dart 18
Loos Co
Loos & Co Tension Gauge PRO PT1M for 2.5 to 4.0 mm wire
Part # LOOPT1M
$195.00
Fit verified for Dart 18
Spinlock
Spinlock Rig Sense Tension - Wire: 1/16 - 3/16 in (2.0 - 5.0 mm)
Part # SPI-RGS-0205
$143.65
$169.00
No Dart 18 parts match these filters.
Can’t find a part for your Dart 18? Request a Dart 18 part
Go fast
Dart 18 tuning guide
No sailmaker or class association publishes a Dart 18 tuning chart. The builder, Windsport, covers the basics: rake by the forestay lacing line, rig tension by the vernier shroud adjusters (start about hole 2 from the top, mast upright, and never so tight the mast can't rotate freely), plus a note on using batten tension to change sail depth. There are no gauge readings or wind-range tables.
Windsport International (builder) — Dart 18 Rigging Manual (part 2: rig tension) PDF posted May 2021
- Written for
- Standard Dart 18 main (9 battens), jib and gennaker
- Tension gauge
- None
- How it’s measured
- Rake is set with the rope lacing line on the forestay; rig tension with the vernier shroud adjusters.
- Source
- Windsport International (builder), PDF posted May 2021
Base setup
- Shroud adjusters
- Vernier adjuster pinned at about hole 2 from the top to start
- Mast rake
- Start with the mast vertical
- Rig tension
- Always loose enough that the mast can rotate freely 180° across the boat
- Battens
- Tension with thumb and forefinger to give a small curve in the pocket; No. 1 at the bottom to No. 9 at the top
- Jib luff
- Downhaul the jib luff, but never tighter than the forestay
- Rudders
- Blades in line with the keel line when locked down (adjust at the connecting bar)
- Mainsail downhaul
- No luff tension when rigging; set it once sailing
- A rigging/assembly manual; it gives a starting point but no wind-range settings.
Windsport International — The Forgotten Control (batten tension) December 2021 (upload date in the URL; signed "Tom")
- Written for
- Dart 18 and Sprint/Dart 15 mainsails
- Tension gauge
- None
- How it’s measured
- Mark each batten where the sail's leech sits on it so the tension can be repeated.
- Source
- Windsport International, December 2021 (upload date in the URL; signed "Tom")
Base setup
- Minimum
- Just enough tension to remove the small vertical creases along the batten pocket
Trim by condition
- Deep vs flat
- More batten tension gives a deeper, more powerful sail with better acceleration (light air, chop or waves); less gives a flatter, lower-drag sail with a higher top speed. A very deep sail in very light air can hook the leech and stall.
- Order
- Tension from the top down: the short top battens need much harder pulls to take shape than the long lower ones.
- Method
- Without adjustable batten ends, brace the batten end against a hard edge (the traveller track), tie the first half of the reef knot, pull the tension in, then lock it with the second half.
- After sailing
- Always release batten tension so the pockets don't stretch and the leech doesn't start to flutter.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.Rig tension gauges for the Dart 18
Technical
Dart 18 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Dart 18 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Dart 18 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesDart18 Class Rules master 2026 (per filename on Official Documents page)
- Class associationdart18class.com
- Builder specificationsDart 18 on dartcatamaran.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Dart 18 part