One-design race shop · Dinghy
RS200 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for RS200
All RS200 equipment
22 parts
Fit verified for RS200
Selden
Selden Pop-rivet, ø4,8 X 9,9 mm, Monel, Dome Head
Part # sel-167-007-10
$45.00
Fit verified for RS200
Selden
Selden Pop-rivet, ø4,8 X 16,5 mm, Monel, Dome Head
Part # sel-167-006-05
$30.00
Fit verified for RS200
Selden
Selden Pop-rivet, ø4,8 X 12,7 mm, Monel, Countersunk
Part # sel-167-022-05
$36.00
Fit verified for RS200
Harken
Harken Swivel Cam Cleat - Base (Small) w/ Cam-Matic 150 - Line: 1/4 to 5/8 in (6 to 16 mm)
Part # HAR205
$163.95
$186.05Fit verified for RS200
Lalizas
Lalizas Cabo Floating Rope Diam. 15/64'' (6Mm), L 98,43Ft (30M), Orange
Part # LAL-94801
$14.28
Fit verified for RS200
Velocitek
Velocitek Mast Bracket for Prostart or SpeedPuck
Part # VELPROMMB
$69.00
Fit verified for RS200
Harken
Harken Block - 57mm Ratchet Block - Swivel (Black)
Part # HAR2135
$86.95
$98.25Fit verified for RS200
Lalizas
Lalizas Cabo Floating Rope Diam. 20/64'' (8Mm), L 98,43Ft (30M), Orange
Part # LAL-70260
$12.46
Fit verified for RS200
Harken
Harken Block - Carbo 40mm Single - Ratchet - Swivel (Black)
Part # HAR2608
$72.95
$83.10Fit verified for RS200
Loos Co
Loos & Co Tension Gauge PRO PT1M for 2.5 to 4.0 mm wire
Part # LOOPT1M
$195.00
Fit verified for RS200
Spinlock
Spinlock Rig Sense Tension - Wire: 1/16 - 3/16 in (2.0 - 5.0 mm)
Part # SPI-RGS-0205
$143.65
$169.00Fit verified for RS200
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95
No RS200 parts match these filters.
Can’t find a part for your RS200? Request a RS200 part
Go fast
RS200 tuning guide
The RS200 is a low-tweak one-design: set rake (masthead to the rudder pedestal/top of the back tank, about 21′ 6″–21′ 10″), shroud tension on a SuperSpars, Loos or ISP gauge (typically 26–30), spreaders by crew weight (roughly 370–405 mm long, 120–150 mm deflection) and, if needed, mast foot one hole forward. There is no single sailmaker chart; the class publishes a guide by Ian Pickard plus fleet surveys of top boats, and tension readings are on different gauges, so record your own.
Rooster Sailing — How to set up a new RS200… plus a few tweaks 15 March 2021
- Written for
- Not stated
- Tension gauge
- Loos gauge (model not named)
- How it’s measured
- Rig tension on; masthead to the black/white gooseneck band about 540 cm; masthead to the top of the back tank (rear hatch housing) for rake. Spreader length from the inboard end to the shroud attachment; deflection with no rig tension, at the midpoint of the line between the shroud attachments.
- Source
- Rooster Sailing, 15 March 2021
Base setup
- Rake
- 21′ 9″ to the top of the back tank (light teams may rake back as far as 21′ 6″)
- Datum
- 540 cm masthead to gooseneck band
- Rig tension
- 29 on a Loos gauge
- Spreaders
- Length 385 mm; deflection 135 mm
- Gybe strop
- About 40 cm
Trim by condition
- Philosophy
- The author's team (a slightly heavier crew) sails one rig setting and manages power with the kicker.
- Mast shape
- With tension on, the mast should be slightly inverted before the main is hoisted.
UK RS200 Class Association — RS200 Settings March 2017 (rig settings of top sailors, fleet survey) Listed by the class as 'RS200 Settings March 2017'; PDF created 8 May 2017
- Written for
- Not stated (individual sailors' boats)
- Tension gauge
- Not stated (numbers in the mid-20s, consistent with SuperSpars/Loos scales)
- How it’s measured
- Self-reported; rake in ft/in, crew weight as entered (the column header says stone or kg). The class's 'Resources and videos' sheet (https://www.rs200sailing.org/documents/p1iht13qkv1mfpb648eg6kh4jl3.pdf) links a class video on how to measure.
- Source
- UK RS200 Class Association, Listed by the class as 'RS200 Settings March 2017'; PDF created 8 May 2017
Survey responses (rake medium / high / low wind; spreader deflection / length mm; rig tension medium / strong / light)
| Sailor | Crew weight (stone or kg) | Result | Mast foot | Rake med | Rake high | Rake low | Defl. | Length | Tension med | Tension strong | Tension light |
|---|---|---|---|---|---|---|---|---|---|---|---|
| George Yeoman | 145 | 5th | One hole forward | 21′ 9″ | 21′ 9″ | 21′ 9″ | 135 | 385 | 29 | 29 | 29 |
| David Jessop | 125 | 9 | Zero | 21′ 8″ | 21′ 6″ | 21′ 9″ | 135 | 390 | 26 | 28 | 24 |
| Edd Whitehead | 135 | 11 | One hole forward | 21′ 10″ | 21′ 10″ | 21′ 10″ | 155 | 395 | 30 | 30 | 30 |
| Claudia Wilson | 120 | 30th | One hole forward | 21′ 7.5″ | 21′ 7.5″ | 21′ 7.5″ | 130 | 395 | 27.5 | 28 | 26 |
| Will Taylor & Caitlin Jones | 120 | 42 | One hole forward | 21′ 6″ | 21′ 6″ | 21′ 6″ | 130 | 390 | 28 | 30 | 26 |
| Jonny Olin | 147 | 63 | Zero | 21′ 9″ | 21′ 9″ | 21′ 9″ | ? | ? | 27 | 28 | 27 |
| Jack Vincent & Kim May-Papailiou | 125 | 79th | Zero | 21′ 10.5″ | 21′ 10.5″ | 21′ 10.5″ | 135 | 390 | 28 | 29 | 27 |
| Isabel Abbatt | 120 | 95 | One hole forward | 21′ 8″ | 21′ 7″ | 21′ 8″ | 135 | 395 | 28 | 28 | 26 |
| Gary McLennan | 150 | 1st Australian | One hole forward | 21′ 7″ | 21′ 5.5″ | 21′ 7″ | 140 | 400 | 21 | 21 | 21 |
| Ian Martin | 130 | 2014 1st, 2013 2nd | One hole forward | 21′ 8″ | 21′ 8″ | 21′ 8″ | 135 | 395 | 29 | 29 | 29 |
| Tim Saxton | 135 | 28th 2016, 8th 2015 | Zero | 21′ 8.5″ | 21′ 8″ | 21′ 9″ | ? | ? | 28 | 28 | 28 |
| Marty O'Leary | 122 | 2nd Irish Nats | Zero | 22′ 11.8″ | 23′ | 20′ | ? | ? | 28 | 28 | 28 |
| Rob Gullan | 142 | 4th 2014 Mounts Bay | One hole forward | 21′ 9.5″ | 21′ 8.5″ | 21′ 9.5″ | 140 | Longest they go | 35 | 40 | 15 |
| Dave Pointer | 140 | Didn't compete | One hole forward | 21′ 8″ | 21′ 8″ | 21′ 8″ | 147 | 395 | 28 | 28 | 28 |
| Jon Ward | 137 | Didn't compete | One hole forward | 21′ 8.5″ | 21′ 8.5″ | 21′ 8.5″ | 135 | 383 | 28 | 28 | 26 |
| Rob Milligan | 76 | N/A | One hole forward | 21′ 8″ | 21′ 7″ | 21′ 8″ | 128 | 400 | 27 | 28 | 24 |
| Jake Miller | 133 | N/A | One hole forward | 21′ 9″ | 21′ 9″ | 21′ 9″ | 135 | 390 | 26 | 26.5 | 26 |
| Fred Fuller | 104 | — | One hole forward | 21′ 8″ | 21′ 6″ | 21′ 8″ | 140 | 380 | 28 | 28 | 28 |
| Ethan | 120 | — | Zero | 21′ 7″ | 21′ 6″ | 21′ 9″ | ? | ? | 28 | 28 | 28 |
Trim by condition
- Comments
- Jessop might go half a hole back with slightly softer tension in lumpy chop; Whitehead never touches the downhaul; entries marked as sea settings: O'Leary, Milligan, Fuller; marked inland: Ward.
- Self-reported, unverified figures; some entries are clearly on a different datum or gauge (e.g. O'Leary's 22′ 11.8″/23′/20′ rake, Gullan's 35/40/15 tension, McLennan's 21).
UK RS200 Class Association (Ian Pickard) — RS200 Tuning Guide – Ian Pickard 28 June 2002 (file titled as a Yachts & Yachting article)
- Written for
- Not stated; competitive all-up crew weight 18–23 stone
- Tension gauge
- SuperSpars rig tension gauge on the shrouds at about shoulder height
- How it’s measured
- Rake with the jib hoisted and rig tension on: tape on the main halyard to the masthead, measured to the top of the rudder pedestal.
- Source
- UK RS200 Class Association (Ian Pickard), 28 June 2002 (file titled as a Yachts & Yachting article)
Base setup
- Rake ('ideal' conditions)
- 21′ 7″ (6579 mm) to 21′ 8″ (6604 mm)
- Rake, light winds
- About 21′ 9″ (6629 mm)
- Rake, heavier conditions
- About 21′ 6″ (6554 mm)
- Spreaders, lighter crews
- Length 370–380 mm; deflection 135–150 mm
- Spreaders, heavier crews
- Length 385–405 mm; deflection 120–130 mm
- Rig tension, ideal
- 27–28 (320/340 lb, 146/155 kg)
- Rig tension, light
- About 24 (270 lb, 123 kg); some as low as 22 (240 lb, 109 kg)
- Rig tension, heavy
- About 28; some light teams reduce it, some heavy teams go to 30 (400 lb, 182 kg)
- Mast foot
- Standard is the back of the track; move one hole forward (two at most) if the boat wants to luff, then re-check everything
Trim by condition
- Mast shape
- With the recommended spreaders the mast sits slightly inverted at the spreaders with rig tension on and no main; that's intended, to resist the full-length battens and kicker.
- Jib luff and fairleads
- Little luff tension (horizontal creases OK) in light, flat water; more in wind and waves. Fairlead all the way back with a long tack shackle, one hole forward with a short one.
- Kicker
- The key control: upwind, second leech telltale flying about half the time (err tighter in flat water); add in gusts. Very light air just enough to flick the battens; ease a little in big waves. Off in light air downwind, more in marginal planing, ease again when overpowered to keep the boom out of the water.
- Outhaul
- Foot just touching the boom upwind; fully eased downwind; tight when really overpowered.
- Cunningham
- Last-resort depowering upwind (the author's view; others use it routinely); pull it hard when overpowered on a reach.
- Sheets and trim
- Jib in tight upwind (2:1 sheets help in big breeze); work the main hard. Keep the boat flat, weight forward in light air, and steer with trim.
UK RS200 Class Association — RS200 settings (shroud-plate holes, tension and rake) Undated
- Written for
- Not stated
- Tension gauge
- Not named (lb)
- How it’s measured
- Hole positions refer to the standard Holt Allen shroud plate counted from the top; they vary between masts because shroud lengths differ.
- Source
- UK RS200 Class Association, Undated
Settings by condition (shroud hole, tension, rake)
| Condition | Shroud hole | Tension | Rake |
|---|---|---|---|
| Light 1 – crew well to leeward | 4 holes front | 200 lb | 21′ 9″ |
| Light 2 – crew on centreline | 4 holes front | 270 lb | 21′ 9.5″ |
| Light 3 – crew windward of centreline on thwart | 4 holes front | 340 lb | 21′ 10″ |
| Med 1 – both sitting on the side | 4 holes back | 270 lb | 21′ 8″ |
| Med 2 – both hiking | 4 holes back | 340 lb | 21′ 9″ |
| Med 3 – hiking hard, occasionally spilling | 4 holes back | 400 lb | 21′ 9.5″ |
| Strong 0 – main permanently eased | 5 holes front | 270 lb | 21′ 7.5″ |
| Strong 1 – main beyond transom corner | 5 holes front | 340 lb | 21′ 8″ |
| Strong 2 – main very eased, battens backwinding | 5 holes front | 400 lb | 21′ 9″ |
- The sheet is a grid of hole position vs tension; the condition-to-cell mapping above follows its numbering (0–3 per column). 'ibs' in the source is read as lb.
UK RS200 Class Association (Dave Derby / Pete Vincent) — RS200 Tuning – Nationals 2001 and 2002 settings tables 2001 and 2002 Nationals
- Written for
- Not stated (settings of top-ten boats at the Nationals)
- Tension gauge
- ISP gauge (shroud tension)
- How it’s measured
- Self-reported. Where a sailor gives two or three rake values they are listed without wind labels; Pete Vincent's commentary says the heavier crews run the mast upright in light air and rake back as the wind increases.
- Source
- UK RS200 Class Association (Dave Derby / Pete Vincent), 2001 and 2002 Nationals
Nationals 2002
| Helm | Crew weight (st) | Mast foot | Rake | Shroud tension (ISP) | Spreaders length/deflection (mm) |
|---|---|---|---|---|---|
| Tom Hewitson | 21 | 1 hole forward | 21′ 7½″ / 21′ 6½″ | 28 | 395/138 |
| Dave Giles | 21½ | Standard | 21′ 8″ / 21′ 6″ | 27 | — |
| Dave Derby | 20½ | 2 holes forward | 21′ 7½″ / 21′ 5½″ | 28 | 375/130 |
| Mike Saul | 20 | Standard | 21′ 7″ | 30 | — |
| Jon Lewis | 20½ | 1 hole forward | 21′ 7½″ / 21′ 5½″ | 28 | 375/138 |
| Pete Vincent | 22½ | Standard | 21′ 9″ / 21′ 9″ / 21′ 8″ | 20 light / 28 medium / 30 fat power | 395/135 |
| Greg O'Brian | 23 | 1 hole forward | 21′ 7″ | 30 | 385/145 |
| Ian Pickard | 22½ | 1 hole forward | 21′ 8½″ / 21′ 7½″ / 21′ 6½″ | 25 light / 27 medium / 27 lard power | 390/125 |
| Colin Staite | 19½ | 1 hole forward | 21′ 7″ / 21′ 6″ | 28 | 370/130 |
| Steve Dunn | 20½ | 1 hole forward | 21′ 7″ / 21′ 5″ | 26 light / 27 breezy | 395/120 |
Nationals 2001
| Helm | Crew weight (st) | Mast foot | Rake | Shroud tension (ISP) | Spreaders length/deflection (mm) |
|---|---|---|---|---|---|
| Geoff Carveth | 20½ | 1 hole forward | 21′ 9″ / 21′ 8″ / 21′ 7″ | 26 light / 28 medium / 28 strong | 395/135 |
| Dave Derby | 20½ | 2 holes forward | 21′ 7½″ / 21′ 5½″ | 28 | 375/130 |
| Craig Burlton | 21½ | Standard | 21′ 9″ / 21′ 7″ | 28 | 380/135 |
| Tom Hewitson | 21 | 1 hole forward | 21′ 7″ | 27 | 385/135 |
| Mark Littlejohn | 21½ | Standard | 21′ 5″ | 28 chop / 31 normal / 35 windy | — |
| Paul Fisk | 19 | 1 hole forward | 21′ 6½″ | 25 light / 28 normal | 370/130 |
| Mike Saul | 19½ | Standard | 21′ 8″ | 22 light / 26 normal | 370/147 |
| Steve Restall | 21 | Standard | 21′ 8″ | 25 | 390/ (deflection blank) |
| Paul Hammett | 18½ | 1 hole forward | 21′ 8″ / 21′ 6″ | 27 (measured on jib luff) | 375/140 |
Trim by condition
- Trends
- Heavier crews run the mast more upright in light air and rake back as it builds, with lower tension in light air; light crews use about 370 mm spreaders and heavier crews 390/395 mm, generally with less deflection (Pete Vincent's commentary).
- 2001 table: https://www.rs200sailing.org/documents/tuning/RS200TuningSheet2001.pdf; commentary: https://www.rs200sailing.org/documents/tuning/RS200Tuning2001.pdf
- Weights in stone are combined crew weight.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.Rig tension gauges for the RS200
Technical
RS200 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the RS200 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current RS200 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesRS Class Association Rules All Classes v4 June 2022; RS200 Appendix to Class Rules (undated)
- Class associationrs200sailing.org
- Builder specificationsRS200 on rssailing.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a RS200 part