One-design race shop · Dinghy
Topper Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Topper
All Topper equipment
8 parts
Fit verified for Topper
Harken
Harken Block - Carbo 29mm Single - 90° Fixed Head
Part # HAR352
$23.95
$26.85Fit verified for Topper
Rooster
Rooster Carbon Tiller Extension (975mm end to end) for Topper
Part # ROO127447
$162.00
$180.00Fit verified for Topper
Rooster
Rooster Spar Bag - Padded - Size: 118.1 in (3.0 m)
Part # ROO132926
$76.50
$85.00Fit verified for Topper
Lalizas
Lalizas Cabo Floating Rope Diam. 15/64'' (6Mm), L 98,43Ft (30M), Orange
Part # LAL-94801
$14.28
No Topper parts match these filters.
Can’t find a part for your Topper? Request a Topper part
Ready to install
Topper running rigging
Sheets, halyards and control lines whose length and diameter we have matched to the Topper specification.
Official Harken dealer
Topper deck layout
90-Degree Fixed Head 29 mm Carbo Block
-
1
29mm BlockHarken 348
$17.95 -
2
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
3
29mm Block — SwivelHarken 340
$29.95 -
6
29mm 90-Degree BlockHarken 352
$23.95
Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.
Go fast
Topper tuning guide
The Topper is an unstayed one-design, so tuning is kicker, downhaul, mainsheet-block spacing and daggerboard height; rake is fixed by the hull. The class's 2025 coaching guide explains that the newer grey rota-moulded hull carries its mast about 130 mm more upright than the old red hull, so red-boat kicker and downhaul habits need adjusting.
International Topper Class Association (ITCA World) — Coaching guide for the rota-moulded Polyethylene International Topper 2025 (PDF dated February 2025)
- Written for
- Class sail on the original (red, injection-moulded) and new (grey, rota-moulded) hulls
- Tension gauge
- None (unstayed rig)
- How it’s measured
- Rake compared using the same mast in both hull types; the guide doesn't give the measuring points.
- Source
- International Topper Class Association (ITCA World), 2025 (PDF dated February 2025)
Base setup
- Mast rake, red hull
- Measured as 5430 mm
- Mast rake, grey hull
- Measured as 5560 mm (the mast sits 130 mm more upright)
- Mast deck ring
- 0–5 mm further forward on the grey hull, depending on moulding shrinkage
- Mainsheet blocks
- On a grey hull, set the blocks about 130 mm further apart to get the same upwind leech tension as on a red hull (a rough reference)
- Hull weight
- Red hulls from sail no. 48000: 48–49 kg; grey hulls: 48.9 kg
Trim by condition
- Kicker and downhaul upwind
- The grey hull has less weather helm, so it generally needs less kicker and downhaul, applied later in the wind range (Malta sailors use almost no downhaul in waves). Using red-boat tension shows extra overbend creases mid-mast and over-flattens the middle of the sail.
- Under 10 kn
- Don't go too loose: the sail gets deep and draggy. If you find yourself over-sheeting, add a little kicker until speed and pointing balance, then note the block spacing.
- 20 kn plus
- Too much kicker still creates weather helm; play daggerboard height, though usually less raised than the deck-level guide used in the red boat.
- Toe strap
- Tie the front of the strap up to the p-clips at the mainsheet block base (about 10 cm further forward) for a flatter hike.
- Downwind
- Move weight aft sooner in big gusts and waves; the grey hull's bow goes down a little earlier.
- A coaching article rather than a wind-range chart; findings from coaches Luke Shaw (RYA North) and Matthew Wallis (Vikings SC, Malta).
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Topper resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Topper by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Topper class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rules2023 Class Rules (June 2023), effective 2023-June-19 (World Sailing, status Approved)
- Class associationitcaworld.org
- Builder specificationsTopper on toppersailboats.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Topper part