One-design race shop · Dinghy
RS Tera Race Shop
Everything you need to prepare, compete, and win.
Fit verified for RS Tera
All RS Tera equipment
10 parts
Fit verified for RS Tera
Selden
Selden 40 Ball Bearing Block - Fiddle Hook Cam Eye
Part # sel-404-101-19r
$110.50
$130.00Fit verified for RS Tera
Barton Marine
Barton Windicator WP200S - Topper, Optimist, Starling & Blokart Class
Part # bam-84001
$48.00
Fit verified for RS Tera
Selden
Selden 30 mm Ball Bearing Block - Linked BBB20/BBB30
Part # sel-403-101-15
$20.40
$24.00Fit verified for RS Tera
Davis Instruments
Davis Black Max Wind Direction Indicator
Part # dav-1295
$69.99
Fit verified for RS Tera
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95
No RS Tera parts match these filters.
Can’t find a part for your RS Tera? Request a RS Tera part
Ready to install
RS Tera running rigging
Sheets, halyards and control lines whose length and diameter we have matched to the RS Tera specification.
Go fast
RS Tera tuning guide
The RS Tera is Paul Handley's 2.87 m rotomoulded junior singlehander (ISAF/World Sailing International Class since 2009) with an unstayed two-part aluminium mast, so there is no shroud tension or rake to set: tuning is kicker, outhaul and downhaul, within class-rule purchase limits (outhaul max 4:1, downhaul max 6:1, kicker max 6:1, mainsheet max 2:1). RS Sailing's Rigging Manual V3 is the only published builder document and its sailing hints are qualitative; neither RS, the class association nor any sailmaker publishes a numeric RS Tera tuning guide.
RS Sailing — RS Tera Rigging Manual V3 V3 (PDF generated 5 Jun 2025)
- Written for
- RS Tera Sport main 3.7 m² (Dacron, reefing), RS Tera Pro main 4.8 m² (Mylar, fully battened), RS Tera Mini sail 2.7 m²
- Tension gauge
- None — unstayed rig, no tension gauge used
- How it’s measured
- No rake or tension measurements; mast height is set by a pin through the mast bottom section.
- Source
- RS Sailing, V3 (PDF generated 5 Jun 2025)
Base setup
- Mast height pin
- Pro mainsail: pin in the upper hole of the mast bottom section. Sport mainsail: pin in the lower hole.
- Kicker
- 2 × 30 mm vang blocks plus vang bottom block; kicker primary 0.95 m and kicker control line 2.40 m
- Downhaul
- Pro sail: through the hole in the mast collar, through the sail eye and back down to the cleat on the mast. Sport sail: tied to the metal ring on the sail sleeve, through the cleat on the front of the mast.
- Outhaul
- Pre-rigged on the boom; hook onto the clew, pull tight and cleat. Performance outhaul kit uses a 2.06 m × 4 mm rope and 20 mm blocks.
Trim by condition
- Launching
- Leave the kicking strap loose while launching and pull it on as appropriate once sailing.
- Upwind
- Get the boom as near as possible to the centreline; the kicking strap should be firmly tensioned for upwind work (luff head to wind briefly to pull it on). If the boat feels lifeless close-hauled you are probably too close to the wind — ease the sheet and bear away to rebuild speed.
- Fore-and-aft trim
- Sail the boat as flat and upright as possible; as a general rule sit further forward in lighter winds and further aft in stronger breezes.
- Downwind
- Let the sail out until about 90° to the centreline; tweak the mainsheet to bring the boom across when gybing.
- Reefing (Sport and Mini only)
- Leave the downhaul cleated, unclip the kicker from the mast-foot eye, release the outhaul, twist the mast so the sail wraps around it to the size wanted, re-attach the kicker and pull on the outhaul.
- Technical data in the manual: LOA 2.87 m, beam 1.23 m, hull weight 40 kg, sailing weight 56 kg, draught 0.75 m, max sailor weight 80 kg (the RS Sailing product page and class site give hull weight 43 kg and max crew 135 kg).
- No outhaul-distance, downhaul or kicker numbers are given; all guidance is qualitative.
- The same V3 manual is mirrored by West Coast Sailing at https://westcoastsailing.net/content/rigging-guides/rigging-guide-rs-tera.pdf.
- Class rule C.9.2 (2014) caps purchases at mainsheet 2:1 (extra block at the outboard boom end), outhaul 4:1 with up to three blocks, downhaul 6:1 with up to two extra blocks, kicker 6:1; the IRSTCA statement of 04.07.2024 allows one extra non-purchase lead block after the outhaul and downhaul systems and tiller extensions up to 1.2 m of the OEM material.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-04). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
RS Tera resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the RS Tera by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current RS Tera class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesInternational RS Tera Class Rules 2014 (ISAF/World Sailing closed class rules; 2014 is the current edition on the class site, with the IRSTCA interpretation statement V2 of 04.07.2024)
- Class associationrstera.org
- Builder specificationsRS Tera on rssailing.com
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a RS Tera part