One-design race shop · Dinghy
A Scow Race Shop
Everything you need to prepare, compete, and win.
Fit verified for A Scow
All A Scow equipment
2 parts
Fit verified for A Scow
Harken
Harken Canvas A-Scow Mooring Cover (Sunbrella / Outdura)
Part # HAC8001A
$2,955.80
No A Scow parts match these filters.
Can’t find a part for your A Scow? Request a A Scow part
Go fast
A Scow tuning guide
A Scows race with two rig types, so pick the guide for yours: the modern swept-spreader rig (no permanent backstay or ram, bend set with the uppers) and the traditional straight rig (backstay and mast ram). Both North guides read tension in pounds on a Loos gauge, but only the intermediates on the swept rig are given a gauge model (Model A); the rest are set by sight or in turns.
North Sails — A Scow Tuning Guide (swept-spreader rig) Current web page, undated
- Written for
- North A Scow main and jib; small VMG and big asymmetric spinnakers (no model names)
- Tension gauge
- Loos Model A for the intermediates (180–200 lb); everything else set by sight or full turns
- How it’s measured
- Rake: deck to the forestay pin junction. Prebend: a string along the back of the mast tunnel, read at the spar's midpoint. Turns are full turns, but the guide doesn't say what they are counted from.
- Source
- North Sails, Current web page, undated
Base setup
- Rig
- Deck-stepped swept-spreader rig; uppers run through the spreader tips to the mast base. The permanent backstay and ram are removed and bend is tuned with the uppers.
- Chainplates
- Intermediates on the aft chainplate hole, lowers on the forward hole
- Prebend
- All-purpose setting 5"
- Storage
- Take the prebend out for winter by slacking the turnbuckles or levers (never pull a lever pin under load)
Rig settings by wind (wind units not stated; Loos Model A for intermediates)
| Setting | Light 0–12 | Medium 10–18 | Heavy 18+ |
|---|---|---|---|
| Mast rake (deck to forestay pin) | 15" | 16.5" | 18–19" |
| Uppers | Ease 2 turns; 4–4.5" prebend | Back up 2 turns; 5–5.5" prebend | Standard spot; 5–5.5" prebend |
| Intermediates | 180–200 lb, Loos Model A | +8 full turns | +8 full turns |
| Lowers | Set so the mast has ½" sag | +6 full turns | +6 full turns |
Mainsail controls
| Control | Light | Medium | Heavy |
|---|---|---|---|
| Cunningham | None | Pull out wrinkles | Hard, to pull draft forward and open the leech |
| Vang | Loose | Play it in puffs to bend the mast and depower | Very firm; vang-sheet in puffs |
| Outhaul | ½–¾" off the boom band | To the black band | To the black band |
| Mainsheet | Top batten twisted open, top telltale flowing | Top telltale stalling half the time, or the aft third of the top batten parallel to the boom | Flatten and twist; work the sheet to keep the boat on her lines |
| Traveller | 8–10" to windward of centreline | Centred, work down in puffs | Work up and down; maximum out is at the rudder posts |
Trim by condition
- Rake
- Light air can go as far forward as 15" (further with heavy crews if you want to experiment). In heavy air rake aft until the mainsheet blocks trim nearly block-to-block, around 19"; too far aft leaves the main twisted open.
- Running backstays
- Light: soft to sag the headstay and power the jib. Medium: ease in lulls, pull hard in puffs. Heavy: very hard to flatten jib and main. Downwind, snug only to support the mast; the windward runner snug in medium–heavy air without inverting the mast.
- Jib
- Set low so the foot curls on the deck; full low in light air, flatter foot and more open upper leech as it builds. Trim until the top-batten telltale stalls, then ease until it flows. Luff just wrinkle-free.
- Jib track
- Inboard limit is the inboard edge of the cockpit; move out in medium/heavy air to stop backwinding, and fully out reaching and running.
- Chop
- More twist in main and jib with fullness low.
- Downwind
- 0–6 kn: small VMG asymmetric, maximum leeward heel, drop the jib if needed. Over 6 kn: big asymmetric, maximum heel, roughly ⅔ to maximum board. Mexican gybe from about 7–8 mph; pre-gybe in very light air.
- Troubleshooting
- Too much weather helm: outhaul max, rake aft, more runner, then raise some board. Can't point: jib car too high, jib too full low, rig too tight, rake too far aft or main too full. Lee helm downwind: not enough board.
- The guide gives wind ranges without units and mixes mph and knots elsewhere.
- The "+8" and "+6" full turns are not tied to a stated starting point; presumably from the light-air setting.
North Sails — A Scow Tuning Guide (traditional straight rig) North One Design web page, printed 28 May 2007
- Written for
- AP mainsail and jib; mid-size runner/reacher and big symmetric spinnakers; small and big asymmetrics
- Tension gauge
- Loos tension gauge (model not stated), pounds
- How it’s measured
- Tune from the deck up (every A Scow has a dip in one rail, so the jib halyard to the chainplates doesn't work). Rake: tape on the main halyard, pulled up, measured to the aft corner of the transom.
- Source
- North Sails, North One Design web page, printed 28 May 2007
Base setup
- Mast position
- Aft side of the mast within 1" of the forward side of the black band (the mast must be forward of the band by rule)
- Intermediates
- Attach first and centre the mast in the deck well; sight for straightness and tighten evenly to about 500–600 lb on a Loos gauge
- Lowers
- Snug so the mast is straight down low
- Uppers
- Tighten evenly to keep the mast straight above the headstay; about 300 lb to start
- Sailing check
- Adjust only uppers and lowers (not intermediates) for a slight sag from tip to boom
- Mast rake (AP sail)
- 42' 8", main halyard to the aft corner of the transom
Control settings by wind
| Control | Light | Medium | Heavy |
|---|---|---|---|
| Mast rake | Close to vertical with the boat flat | Rake aft as it builds if the boat feels jumpy or crabby | Aft until the mainsheet blocks are nearly block-to-block |
| Cunningham | None | Pull out wrinkles | Hard, to move draft forward and open the leech |
| Vang | Loose | Snug to stop the boom skying | Very firm, vang-sheet in puffs |
| Outhaul | Pull out vertical wrinkles | Wrinkles out, or to the black band to flatten | To the black band |
| Running backstay | Soft, to sag the headstay and power the jib | Ease in lulls, hard in puffs | Very hard |
| Permanent backstay | Loose | Loose | Some tension to flatten and twist the top of the main if needed |
| Mast ram | Free-float, or forward if the main is too full behind the mast | Cleated neutral to vang against | Neutral to some aft so the main doesn't invert low |
| Traveller | About 8–10" to windward of centreline | Centred, work down in puffs | Work up and down; maximum out is at the rudder posts |
| Mainsheet | Top batten open, top telltale flowing | Top telltale stalling half the time, or the aft third of the top batten parallel to the boom | Flatten and twist; work the sheet hard |
Trim by condition
- Downwind rig
- Mast vertical in light–medium air and with symmetric spinnakers in heavy air; with the asymmetric in heavy air keep the rake aft and reach. Mark the backstay for the most-forward (vertical) position. Pull the ram forward so the mast doesn't invert when the backstays are eased.
- Jib
- Low to the deck with the foot curling on it in light air; flatten the foot and twist the top open as it builds; trim to the stall of the top-batten telltale then ease until it flows. Luff just wrinkle-free. Track inboard limit is the cockpit's inboard edge; outboard in medium/heavy air and fully out off the wind.
- Symmetric spinnaker
- 0–6 kn: mid-size runner/reacher, maximum leeward heel, pole about a foot off the headstay. Over 6 kn: big spinnaker, run deep in pressure, board ¼ down, main fully out, pole aft in puffs.
- Asymmetric spinnaker
- 0–6 kn: small asymmetric, maximum leeward heel, drop the jib if needed. Over 6 kn: big one, maximum heel, ⅓ board.
- Troubleshooting
- Weather helm: check the ram isn't pushing the mast aft, add runner, then rake aft, then lift the board slightly. Can't point: jib car too high, jib too full low, ram too far aft or too much runner. Lee helm downwind: not enough board.
- A 2007 print of North's old northsailsod.com One Design page, kept by the A Scow class for boats still on the straight rig. The guide doesn't give a wind-range table.
- The Loos model isn't named, so the 300 lb / 500–600 lb figures can't be compared directly with the swept-rig Model A reading.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
A Scow resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the A Scow by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current A Scow class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesNCASA Class Rules, file code 07-12-19 (date format ambiguous)
- Class associationascow.org
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a A Scow part