One-design race shop · Dinghy
Lido 14 Race Shop
Everything you need to prepare, compete, and win.
Lido 14 parts
Tell us what your Lido 14 needs
We list parts for a class only after checking them against the builder’s specification and the class rules. Send us the part, position or part number and our rigging team will source it.
Go fast
Lido 14 tuning guide
The Lido 14 sails with deliberately loose shrouds so the mast leans aft upwind and forward downwind, so tuning means setting aft rake (about 20′4″ on a classic boat) and forward rake (about 21′), with the centreboard angle, foot curl of the jib and outhaul gap doing the rest. Rake numbers only transfer between boats with the classic masthead and halyard: on 6000-series boats Quantum adds 3″ while Ullman uses a calibrated forestay or a 7½″ aft-to-forward difference instead.
Ullman Sails — Lido 14 Racing Guide May 30, 2008 edition (Dave Ullman and John Papadopoulos, with DoubleWave)
- Written for
- Ullman Lido 14 main and jib
- Tension gauge
- None (shroud tension set by rake measurements)
- How it’s measured
- Classic boats: tape (with a hole) on the main halyard shackle (assumed ¾″ long; adjust for your hardware), hoisted to the top, tape pulled gently to load the opposing rigging, measured to the aft lip of the transom on centreline. 6000-series or non-classic halyard: use DoubleWave's calibrated forestay, or set the mast a degree or two aft of perpendicular to the deck, or use the weather-helm test.
- Source
- Ullman Sails, May 30, 2008 edition (Dave Ullman and John Papadopoulos, with DoubleWave)
Base setup
- Aft rake, classic
- 20′3½″ to 20′4½″ (mast resting on the forestay and one shroud); start mid-range; novices at the forward end, 20′4½″
- Forward rake, classic
- 20′11″ to 21′ (mast resting on both shrouds); or set shrouds so you can grip a palm width of forestay and turn it 90°, or so the jib sheets don't touch the leeward shroud close-hauled
- 6000 series
- Aft rake very slightly aft of vertical; forward rake about 7½″ more than aft rake (quick-tune table says about 7″)
- Centreboard angle
- Leading edge 90° to the hull; precise check: marks 36″ aft on the hull and 36″ down the board's leading edge should be 52″ apart
- Centreboard fore-aft
- Leading edge as far aft as class limits allow
- Jib leads
- As far forward as the rules allow, and inboard toward the limits, equal port and starboard (the hull is asymmetric)
Quick tune
| Setting | Classic Lido 14 | 6000 Series Lido 14 |
|---|---|---|
| Aft mast rake | 20′4″ | Very slightly aft of vertical |
| Forward mast rake | 21′ | About 7″ forward of aft rake position |
| Jib halyard | Very slight wrinkles at lower jib hanks | Same |
| Outhaul | 4″ between the foot of the main and the boom | Same |
| Centreboard | Leading edge 90° to the hull | Same |
| Traveller | Centred | Same |
| Cunningham | Just enough to keep the sail in its track | Same |
Outhaul (max gap between main foot and boom, close-hauled)
| Wind condition | Gap |
|---|---|
| Drifting (0–3 kn) | 6″ |
| Underpowered (3 kn to both on the rail) | 6″ to 4″ |
| Powered (on the rail to hiking hard, flat) | 4″ to 2″ |
| Overpowered (hiking hard, not flat) | 2″ to 0″ |
Trim by condition
- Weather helm
- Set rake so that fully powered and flat the tiller swings slowly to leeward when released.
- Jib halyard
- Draft about 40% back; very slight crow's feet in the lower third, tightened as wind rises.
- Jib sheet
- As tight as conditions allow, judged by the curl of the jib foot (diagram in the guide). Reaching without the whisker pole: crew holds the sheet between lead and clew; with the pole, draft at 50%.
- Main
- Halyard to the top always; cunningham keeps wrinkles in the lower third; vang slack upwind; sheet so the top batten is parallel to the boom (top-batten ribbon between streaming and just drooping behind the leech); traveller centred except when overpowered.
- Off the wind
- Vang keeps the top batten parallel to the boom; ease the sheet to the edge of luffing; board about 1/3 up on a beam reach and fully up running.
- Crew position
- Underpowered: skipper just aft of the jib lead, crew just forward; drifting move 6–12″ forward; overpowered move aft.
- Ullman's Newport Beach page links its own copy at oldarchive.ullmansails.com, which returned HTTP 401, so the link is to the canadianboating.ca copy.
- The quick-tune table says about 7″ between 6000-series aft and forward rake, the text says 7½″.
Quantum Sails — Lido 14 Tuning Guide Quantum San Diego (George Szabo); PDF dated March 2008
- Written for
- Quantum Lido 14 main and jib
- Tension gauge
- None (shrouds set by rake measurements)
- How it’s measured
- Tape (at least 25 ft) on the main halyard shackle, hoisted to the sheave and cleated; aft rake with the mast leaning back on the forestay, read at the aft edge of the transom on centreline; forward rake with someone pulling the forestay so the mast rests on the shrouds.
- Source
- Quantum Sails, Quantum San Diego (George Szabo); PDF dated March 2008
Base setup
- Aft rake
- 20′3½″ to 20′4½″ (move the forestay in the adjuster)
- Forward rake (shrouds)
- 20′11″ to 21′
- New Lido (6000 and above)
- Add 3″ to both measurements (halyard tied through the tape with a figure eight, no shackle); adjust again if your boat has a shackle
- Diamonds
- Not critical as long as equally taut
- Centreboard
- Maximum depth (50.25″), maximum aft at the board/hull point (95″), bottom maximum forward (52″)
- Rudder, mast step, jib leads
- Bottom of the rudder, mast step and jib leads all at their maximum forward positions
- Whisker pole
- Maximum length, 72″ from mast to pole end
- Tiller extension
- Up to about 36″ (old 30″ limit lifted in 1993)
Trim by condition
- Jib halyard
- Very slight crow's feet (max 2″ long) from the bottom snaps; upper snaps almost smooth; tighter as wind builds.
- Jib sheet upwind
- Very light: foot full with no curl; 5–7 kn: foot curl just kicking up; medium: curl kicking up without a tack-to-clew crease; strong: a slight crease. Ease an inch for a power boost.
- Jib downwind
- Hand-trim reaching in light air; whisker pole back so the clew sits just behind the bow when running (further back by the lee).
- Cunningham
- Speed wrinkles from the bottom half of the luff only (most of the luff under 5 kn); fully eased reaching and running.
- Outhaul
- Foot about 7″ from the boom in light air, closing to about 6″ in a decent breeze.
- Vang
- Upwind take out the slack with the main trimmed so the leech holds when eased; more in big breeze (don't break the boom); ease before the windward mark. Reaching keep the top batten parallel to the boom.
- Mainsheet
- Top batten parallel or just hooking to weather of the boom; in light air ease until parallel to centreline.
- Traveller
- Pinned in the centre under 6 kn; above that sliding about 1 1/2″ either side until badly overpowered.
- Centreboard
- Beam reach: handle end just past the front of the trunk opening; all the way up running.
- Heel
- Slight heel upwind except in steady breeze and flat water; flat in puffs and from 7 kn reaching; windward heel downwind from about 7 kn.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Lido 14 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Lido 14 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- We have no current one-design class rules on file for the Lido 14. Racing legality depends on your class or handicap rules; check them before changing equipment.