One-design race shop · Dinghy
Albacore Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Albacore
All Albacore equipment
19 parts
Fit verified for Albacore
Velocitek
Velocitek Mast Bracket for Prostart or SpeedPuck
Part # VELPROMMB
$69.00
Fit verified for Albacore
Ronstan
Ronstan CleartStart Analogue Sailing Watch, 43mm - Unisex (Black/Red)
Part # RSGRF4056
$169.96
$199.95Fit verified for Albacore
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for Albacore
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for Albacore
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for Albacore
Lalizas
Lalizas Cabo Floating Rope Diam. 20/64'' (8Mm), L 98,43Ft (30M), Orange
Part # LAL-70260
$12.46
Fit verified for Albacore
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for Albacore
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Albacore
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for Albacore
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for Albacore
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95Fit verified for Albacore
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95
No Albacore parts match these filters.
Can’t find a part for your Albacore? Request a Albacore part
Go fast
Albacore tuning guide
Albacores are tuned with mast rake, shroud/jib-luff tension, spreader length and deflection, and the strut or partners for prebend; UK boats can adjust shrouds afloat while North American boats rake with pins and the jib halyard. Rake is measured to different points in each guide (top of transom, inside lower corner, floor at the transom, or forward to the bow), and tension figures are in lb on unnamed gauges, so only compare numbers within one guide.
North Sails — Albacore Tuning Guide (George Carter) and Tuning Matrix Blog post 12 May 2017; PDF with matrix dated 2015 (George Carter, 2015 International Champion)
- Written for
- North Albacore main and low-aspect jib; developed on a Superspar M2 mast and B2 boom
- Tension gauge
- None; tension is set by shroud pins, halyard marks and jib wire sag
- How it’s measured
- Mark the mast at the average sheer-line height, swing the headstay to the mark, then with the jib hoisted and the shrouds just taut measure from the headstay mark to the top of the deck at the bow (about 6″ is the light-air maximum-forward setting). Scale the halyard adjuster in 1″ steps from there.
- Source
- North Sails, Blog post 12 May 2017; PDF with matrix dated 2015 (George Carter, 2015 International Champion)
Base setup
- Centreboard
- Leading edge (board at 90° to the hull) at least 2600 mm from the transom along the hull; normally within about 15 mm of that
- Mast butt
- Maximum forward 3350 mm (aft face of transom to front of mast foot); recommended start 3335 mm
- Rake datum
- Headstay mark about 6″ from the top of the bow deck (max-forward light-air setting); 8–10″ is common at the top of the wind range
- Spreaders
- Length about 15–15.5″, sweep about 7″ (standard spreaders may need shortening); for crews up to about 360 lb, add 0.5–1″ of length above that
- Spreader check
- At the max-forward light-air setting the shrouds should show no deflection in any plane
- Shroud pins
- One pin down above about 15 kn, two pins above about 20 kn
North Sails Albacore Tuning Matrix
| True wind (kn) | 0–7 | 7–11 | 11–16 | 16–20 | 20+ |
|---|---|---|---|---|---|
| Centreboard | Forward | Forward | Forward | Vertical | Slightly aft |
| Shrouds | 0 | 0 | 1 pin down | 2 pins down | 2 pins down |
| Jib wire (rake) | 6″ rake | 6″ rake | 6–7″ rake + | 7–9″ rake | -9–10″ rake (as printed) |
| Jib sag | 1.5″ | 1.5″ | 1.5–2.5″ | 2.5–4″ | 4–6″ |
| Jib cars | 0 | 0 | Back 2–4″ | Foot is tight | Same as 16–20, eased |
| Outhaul | Just snug | Snug | Tight | Very tight | Very tight |
| Prebend | 100% | 1–2″ from partner | 1.5″ from partner | .5″ | .5″ |
| Cunningham | Draft 50% of chord | Draft 50% of chord | Tight | Very tight | Very tight |
| Vang | Loose | Top batten parallel | Enough to de-power | Until main inverts | Until main inverts + |
Trim by condition
- Prebend
- Upwind, pull the mast forward to sit about 1–2″ from the front of the partners; fully bent in very light air; allow it to within 0.5″ in strong wind (further risks over-bending when the headstay is eased). Signs of too little: a full luff and leech telltales about a third back that won't fly.
- Jib sag
- About 2″ at mid-luff upwind in light to moderate air; 2–4″ reaching; 8″+ wing-on-wing with the halyard eased at least 6″.
- Jib lead
- Fold the head to the tack, mark the luff midpoint and draw a line through the clew to the track; the best light–moderate lead is about 4–6″ aft of that point, up to about 10″ aft in very strong winds. Keep the foot on the deck upwind.
- Cunningham
- Main maximum depth just forward of halfway (more bend needs more cunningham); jib depth about a third back. Release both off the wind.
- Outhaul
- Taut in very light air, very tight above 15 kn upwind, eased reaching; maximum power is about 2–3″ of release.
- Vang
- Loose in light air, then enough to keep the top batten parallel, increasing progressively; adjust constantly reaching; slight twist wing-on-wing.
- Wing-on-wing
- Boom near 90°, jib foot snug, mast rammed to the back of the partners, board fully up, boat heeled to windward.
- The matrix is the last page of the PDF version, not on the North blog page; the same PDF is hosted at https://albacoresailing.com/wp-content/uploads/2020/04/North-Albacore-Tuning-guide.pdf and on albacore.org.uk (North Tuning.pdf).
- Some digits in the PDF are spaced oddly ("1 5mm", "1 2 knots"); read as 15 mm and 12 kn.
Hyde Sails — Albacore tuning information (Code 1B mainsail) 2016 (file name; PDF dated March 2016)
- Written for
- Code 1B mainsail on M7 or M2 masts
- Tension gauge
- Loos gauge (model and units not stated)
- How it’s measured
- Rake from the top of the mast to the inside lower corner of the transom. Deflection from a straight edge across the shrouds to the back of the mast.
- Source
- Hyde Sails, 2016 (file name; PDF dated March 2016)
Base setup
- Spreaders, M7
- Length 470 mm; deflection light 165 mm, medium 127 mm, strong 140 mm
- Spreaders, M2
- Length 380 mm; deflection light 165 mm, medium 127 mm, strong 165 mm
- Prebend target
- About 25 mm at the medium setting; light teams may shorten spreaders by 10 mm
- Mast heel
- As far forward as practical within the rules
- Rig tension
- 250 on a Loos gauge from 0–12 kn; 300 above 12 kn
Mast rake (masthead to inside lower corner of transom)
| Conditions | Rake |
|---|---|
| Flat calm until both sitting on the side deck | 7020 mm |
| Full power sitting out, sails still in hard | 7000 mm |
| Full power through to overpowered | 6950 mm |
| Constantly overpowered to top of racing range | 6885 mm |
Trim by condition
- Kicker
- Light air: just enough to stop the boom rising in tacks and gybes; as wind builds, snug it only to control the leech.
- Centreboard
- Fully down or raked forward; vertical as the wind increases; raise slightly once overpowered.
- The deflection figures are odd (medium smaller than light and strong) but are printed that way; Hyde says the 25 mm prebend target matters more than the exact figure.
- The rig-tension figures (250 / 300 'on a Loos gauge') carry no units or scale; check which Loos scale your gauge uses before copying them.
Pinnell & Bax — Albacore Tuning Guide 2025 (PB-HEADOFICEFORMS-TUNINGGUIDES-2025-ALB); earlier 2009-rules edition on albacore.org.uk
- Written for
- P&B Albacore sails; Selden/Superspar M7 (medium) or Selden (stiff) mast
- Tension gauge
- Not named in 2025 (lb on shrouds); the 2009 edition says Super Spar gauge, 3.0 mm wire
- How it’s measured
- Hoist a tape so it reads 5640 mm from the top black band to the top of the gooseneck band, then swing it to the bottom of the floor at the transom. Spreader A: from the line between spreader ends perpendicular to the mast track; B: mast side wall to spreader end.
- Source
- Pinnell & Bax, 2025 (PB-HEADOFICEFORMS-TUNINGGUIDES-2025-ALB); earlier 2009-rules edition on albacore.org.uk
Base setup
- Mast foot
- Front of mast from rear of transom 3320–3300 mm; do not exceed the 3300 mm class rule (as printed)
- Spreader A (angle)
- 140 mm
- Spreader B (length)
- 240 mm (410 mm if combined crew weight is under 25 stone), as printed
Settings by wind (rig tension in lb on the shrouds)
| Wind (kn; unit from the 2009 edition) | 1–4 | 5–10 | 11–15 | 16–25 | 25+ |
|---|---|---|---|---|---|
| Mast rake (mm) | 7086 | 7035 | 6895 | 6960 | 6935 |
| Rig tension | 240 lb | 250 lb | 300 lb | 350 lb | 350 lb+ |
| Strut (from neutral/upright) | Ease to let the mast bend and remove main fullness | Smallest pressure, a little bend | Straight mast | Straight mast | Straight mast |
| Kicker | Take up slack | Light | Medium | Loads | As much as you can |
| Reason (kicker/boom) | Ease the boom slightly to promote flow | Boom on the centreline | Boom on the centreline; if you need to ease, rake more | Top telltales stalling 50% | Flatten the sail and ease the boom to keep the boat flat |
| Cunningham (close-hauled) | None | None | A little to remove creases | Light | Medium |
| Outhaul | 33 mm from band | 40 mm from band | 40 mm from band | 30 mm from band | 20 mm from band |
| Jib sheeting point | 1 hole forward of middle | Middle | Middle | 1–2 holes back | 2–3 holes back |
| Centreboard | Full down | Full down | Up 25 mm or 1″ | Up to 50 mm or 2″ | Up to 75 mm or 3″ |
- The 2025 sheet gives no wind-speed unit; the 2009 edition labels the same bands in knots.
- Likely typos in the 2025 sheet: 11–15 kn rake 6895 mm (the 2009 edition has 6985 mm, which fits the sequence) and spreader B 240 mm (the 2009 edition has a 420 mm spreader length, 410 mm for crews under 25 stone).
- 2009-rules edition: https://www.albacore.org.uk/images/documents/Tuning%20Guides/PnB%20Albacore%20Rigging%20Guide.pdf — same table with imperial rakes (23′ 3″, 23′ 1″, 22′ 11″, 22′ 10″, 22′ 9″), 30 mm outhaul at 1–4 kn, Super Spar gauge on 3.0 mm wire, mast Super Spar M7 (medium) / Selden Alto (stiff); data from a Speed/Ovington hull used by Will Gulliver and Steve Graham (2nd 2009 Internationals, 1st 2009 UK Nationals, 2nd 2010 UK Nationals).
- The mast-foot line contradicts itself (3320–3300 mm vs a 3300 mm maximum); check the class rule.
Speed Sails (Sailboats) — Albacore Tuning Guide by Sailboats Speedsails Undated web page; PDF copy on albacore.org.uk created Oct 2007
- Written for
- Not stated (Speed Sails guide); spreader settings given for Superspar M7 and Proctor D Sleeved masts
- Tension gauge
- Not named; lb on the shroud at eye level
- How it’s measured
- Jib hoisted, rig tension on with the shroud levers down; tape on the main halyard reading 5640 mm to the top of the black band at the gooseneck, then swing to the top of the transom.
- Source
- Speed Sails (Sailboats), Undated web page; PDF copy on albacore.org.uk created Oct 2007
Base setup
- Mast step
- Class maximum forward 3330 mm (aft face of transom to front of mast); go as far forward as possible but not to the last mm
- Centreboard
- Transom to leading edge just under 8′ 9″ (2660 mm) with the board lowered
- Spreaders, Superspar M7
- Length 420 mm, deflection 140 mm
- Spreaders, Proctor D Sleeved
- Length 425 mm, deflection 140 mm
- Light crews
- Shorten spreaders 10 mm (one hole Superspar, one full hole Proctor)
- Rig tension
- 240 lb in all conditions; ease to about 200 lb when running
- Prebend
- 1″ at spreader height (main halyard held at the gooseneck)
Mast rake (to top of transom)
| Wind | Rake |
|---|---|
| Light | 23′ 6″ (7163 mm) |
| Medium | 23′ 3″ (7086 mm) |
| Strong | 23′ 0″ (7010 mm) |
Mast strut
| Conditions | Strut |
|---|---|
| Drifting | Pull forward about 1″ to flatten the main |
| Medium (5–15 kn) | Pull back ½″ from neutral |
| Increasing wind | Let forward to neutral, then up to ¾″ beyond |
Outhaul
| Point of sail | Setting |
|---|---|
| Upwind | To the black band |
| Upwind, drifting | Eased ¼″ |
| Reaching | Eased 1½–2″ |
| Running | Eased ½″ |
Trim by condition
- Jib fairleads
- Start with the three windward telltales breaking together (the PDF adds: or the sheet roughly bisecting leech and foot); move aft above 15 kn, one hole further forward under 5 kn.
- Main halyard
- Hoist only to the bottom of the black band; below 10 kn drop it ½″ (one notch).
- Kicker
- Very light air: just take the slack out upwind; as the mast starts to bend keep the top leech telltale flying about 80% of the time; above 15 kn it flies all the time and the kicker becomes the power control.
- Cunningham
- Only once overpowered, to remove some of the horizontal luff creases.
- A 2007 PDF version is at https://www.albacore.org.uk/images/documents/Tuning%20Guides/Speed%20Tuning%20Albacore.pdf (its metadata title still reads 'Enterprise Tuning Guide'); it prints the strong-wind rake as 23” where the web page has 23′ 0″.
Elvström-Sobstad — Elvström-Sobstad Albacore Tuning Guide Rev. 4/1/07 (sails cut after January 2003)
- Written for
- Elvström-Sobstad Albacore sails cut after January 2003 (high-aspect jib)
- Tension gauge
- A wire tension gauge (lb) for the initial side-stay setting
- How it’s measured
- Bow to sheer: deck at the bow to a sheerline mark on the forestay (black band at max height). Tip to transom: masthead (step max forward) to deck level at the centre of the transom, gunwale-to-gunwale line, not the scoop.
- Source
- Elvström-Sobstad, Rev. 4/1/07 (sails cut after January 2003)
Base setup
- Centreboard
- Leading edge within 5 mm of the maximum-aft position (2600 mm ahead of the aft face of the transom); up to 5° forward of vertical in light air; in heavy air raise until about ¾ is still in the water
- Mast position
- Maximum forward, foreside of the mast at the base 3350 mm ahead of the aft face of the transom (aft face of the mast about 25.75″ ahead of the board's leading edge)
- Spreaders
- At 9/16 of the height from deck crown to hounds (about 90–92″ above deck); for a 280–300 lb crew, 1.5″ longer than neutral and 1.25″ forward of neutral
- Prebend
- Main designed for 2″ of prebend in under 6 kn
- Side stays
- Pin them so that with the jib halyard tensioned to the 8″ rake setting they are just firm, about 20 lb on a wire gauge; then use that pin in most conditions
- Barber haulers
- If used, 6–9″ ahead of the shroud
Mast rake
| Wind | Bow to sheer | Tip to transom |
|---|---|---|
| Normal (6–18 kn) | 8–9″ | 264–266″ |
| Light, flat water | 7–8″ | 266–268″ |
| Heavy (25+ kn) | 10.5–12″ | 261–258″ |
Spreader tip to mast and chord depth (two versions printed)
| Wind | Tip to mast | Chord depth | Tip to mast (2005 note) | Chord depth (2005 note) |
|---|---|---|---|---|
| Normal (6–18 kn) | 16.5″ | 5.5″ | 15.25″ | 6.0″ |
| Light, flat water | 17″ | 6.5″ | 17″ | 6.5″ |
| Heavy (25+ kn) | 16″ | 6.5″ | 16″ | 6.5″ |
Jib lead (sheet vertex about 1″ above seat top)
| Wind | Centreline to sheet | Transom to sheet |
|---|---|---|
| Normal (6–18 kn) | 15–16″ | 96″ |
| Light, flat water | 15–14″ | 98″ |
| Heavy (25+ kn) | 16–18″ | 93″ |
Trim by condition
- Jib luff sag
- Light air: plenty of slack (more than 3″ off a straight forestay at mid-height), especially in short chop. Moderate: tighten to point but keep the 3–4″ the sails are cut for; usually sail with 2–4″. Overpowered: ease the halyard so the mast bends and the rig can 'pant' in waves.
- Jib trim
- Don't over-sheet close to the centreline; keep some backwind on the main (up to about 36″ above the boom and 9″ back from the mast).
- The page prints the spreader table twice with different normal-wind values; the second is annotated by a sailor who used the normal setting for all of 2005. The spreader table's footnotes appear copied from the rake table.
- The heavy-air tip-to-transom range is printed as 261–258″.
McNamara Sails — Albacore Setting Up Guide Undated (class "well into its fourth decade"; PDF created April 2008)
- Written for
- McNamara main and jib; Proctor D, Proctor Sleeved D, Proctor Stratos, Superspar M7 or M2
- Tension gauge
- No tension figures given
- How it’s measured
- Based on the bottom black band at 610 mm above the sheerline. Two rake measures: front of mast at the heel to outside of transom, and top black band to bottom of transom at the hog.
- Source
- McNamara Sails, Undated (class "well into its fourth decade"; PDF created April 2008)
Base setup
- Jib fairlead track
- Parallel and as close as possible to the centreline, centred 8′ 0″ from the transom and at least 10″ from the inside of the hull
- Jib luff
- About 25 mm horizontal wrinkles; about 5–7 mm of cloth movement on the luff wire when checked 1 m up
Mast position and rake
| Wind | Heel to outside of transom | Top band to bottom of transom (hog) |
|---|---|---|
| Light | 10′ 9.5″ | 23′ 0″ |
| Medium | 10′ 10″ | 22′ 10″ |
| Strong | 10′ 11″ | 22′ 7″ |
Spreaders (length from side of mast; deflection to back of mast)
| Mast | Length | Light | Medium | Strong |
|---|---|---|---|---|
| Proctor D, Superspar M7 | 1′ 5″ | 6.5″ | 5″ | 5.5″ |
| Proctor Sleeved D | 1′ 5″ | 7″ | 6.5″ | 7″ |
| Proctor Stratos, Superspar M2 | 1′ 3″ | 7″ | 6.5″ | 7″ |
Trim by condition
- Jib sheeting
- Sails are designed for the leech at ¾ height about 10° open, parallel at half height and about 10° closed at ¼ height; the sheet line through the clew should meet the luff at the half-height telltale.
- Jib luff
- Rig tension stretches the luff wire and tightens the luff; re-check the tack lashing after setting up and tape the knots.
- Measurements assume the bottom black band at 610 mm above the sheerline (the guide says the class tolerance is 105 mm).
North Sails — Albacore Sail Tuning Guide – North (older edition) Page updated 22 Feb 2010
- Written for
- North Albacore sails; written for a 300–330 lb crew
- Tension gauge
- Not named; about 200 lb on the jib halyard
- How it’s measured
- Hoist the jib to about 200 lb, swing the forestay back to the top of the gooseneck black band and mark it, re-attach and measure along the forestay from the mark down to the deck fitting.
- Source
- North Sails, Page updated 22 Feb 2010
Base setup
- Centreboard pin
- Centre of bolt 254 cm from the transom
- Mast step
- Aft pin 74 cm from the centre of the board pin
- Spreaders
- 43 cm long; straight line between shrouds to the back of the mast "19. cm" (as printed)
- Rake
- 86 cm from the forestay mark to the deck (75 cm for Ontario Yachts hulls)
- Prebend
- 1 cm with new sails; 2–2.5 cm as sails age
- Jib track
- Front at 0 cm relative to the board pin, 30 cm long (about 10 cm aft of the pin on some hulls incl. Ontario Yachts)
Trim by condition
- Cunningham
- None until 11 kn; above that just enough to remove luff wrinkles.
- Vang
- None upwind below 11 kn.
- Prebender
- Only in very light air; none from about 8 kn; restriction may help at 8–11 kn in lumpy seas.
- Outhaul
- Never let the foot shelf open upwind.
- The page refers to a settings table "on the last page" that is not included online.
- Not the same as the George Carter guide: different measuring method and longer spreaders.
Barney Harris (USA 8011) — Albacore Tuning Guide by Barney Harris Printed 3/4/2001 from a 1998 web page; based on the late-1980s North guide
- Written for
- North championship main and low-aspect jib on a post-1989 Ontario Yachts hull with Superspar M2 (US/Canadian boats without adjustable shrouds)
- Tension gauge
- Not named; shroud tension in lb
- How it’s measured
- Rake from a sheer-line mark on the mast: swing the forestay forward to the mark, then measure from the mark to the bow deck tip with 100–200 lb on each shroud.
- Source
- Barney Harris (USA 8011), Printed 3/4/2001 from a 1998 web page; based on the late-1980s North guide
Base setup
- Spreaders
- Starting length 17″, draft 6.5″; more draft for high wind and flat water with light crews, less in steep chop
- Mast step
- As far forward as the rules allow, 3350 mm from the aft face of the transom; partners allow 3225–3330 mm of travel
- Rake
- 152 mm for newer Ontario hulls, 178 mm for older Skene hulls
- Jib sag
- Start with 1–2″
Trim by condition
- Drifting
- Prebend nearly to the partners; vang and cunningham slack, outhaul tight; 3–4″ of sag accelerating, about 2″ at speed.
- Light
- Keep prebend; vang so the top telltale flies about 50%; 0.5–1″ sag in flat water, up to 3–4″ in chop.
- Moderate
- Vang so the leech telltales fly all the time. Jib sag printed as '1 to ½ inches' (probably 1–1½″); leeward shroud just not quite tight. In 12–15 kn flat water with a light crew, ease to 3–4″ of sag and control the jib luff with the mainsheet.
- High wind
- Pin the shrouds down one or two holes before the start (North American boats can't adjust them while racing); pull the vang very hard.
- Reaching / running
- 3–4″ of sag reaching; ram the mast aft; running ease the jib halyard until the mast sits on the gate and the luff sags 6–8″.
- A personal guide, not a sailmaker's; it describes North America's no-adjustment shroud rule, which differs from UK practice.
- The moderate-wind sag figure is printed as '1 to ½ inches', most likely a lost '1' in '1½'.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Albacore resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Albacore by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Albacore class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesAlbacore Class Rules 2025 (UK National Albacore Association / RYA)
- Class associationalbacore.org.uk
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Albacore part