One-design race shop · Dinghy

Lightning Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Lightning

  • 18 verified parts
  • 1 brand
  • Fit checked Nov 2026

Fit verified for Lightning

All Lightning equipment

18 parts

Can’t find a part for your Lightning? Request a Lightning part

Official Harken dealer

Lightning deck layout

Length
19 ft (5.8 m)
Beam
6 ft 6 in (2 m)
Displacement
700 lb (318 kg)
Sail Area (main & jib)
177 sq ft (16.4 sq m)
Spinnaker
300 sq ft (28 sq m)

Adjustable Ball Bearing Lead Car

Adjustable Ball Bearing Lead Car — Harken layout for the Lightning
Drawing: Harken
  1. 1 40mm Traveler BlockHarken 2649 $49.95
  2. 3 40mm BlockHarken 2650 $31.95
  3. 4 57mm Ratchamatic® Block — SwivelHarken 2625 $121.95
  4. 5 Standard Cam Base — SwivelHarken 144 $180.95
  5. 6 29mm Cheek BlockHarken 350 $18.95
  6. 8 Standard Cam-Matic® Cleat - 150Harken 150 $44.95
  7. 9 25mm Wire Block — ShackleHarken 300 $47.95
  8. 11 29mm Double Block — SwivelHarken 342 $53.95
  9. 13 13mm Car — Pivoting ShackleHarken 2700 $150.95

Belowdeck Vang System

Belowdeck Vang System — Harken layout for the Lightning
Drawing: Harken
  1. 1 25mm Wire Block — ShackleHarken 300 $47.95
  2. 2 29mm BlockHarken 348 $17.95
  3. 3 29mm Block — Swivel, BecketHarken 341 $33.95
  4. 4 29mm Cheek BlockHarken 350 $18.95
  5. 5 29mm Double Upright Lead Bullet BlockHarken 220 $53.95
  6. 6 29mm Double Block — SwivelHarken 342 $53.95
  7. 7 29mm Triple Block — SwivelHarken 344 $70.95
  8. 8 29mm Double Upright Lead Bullet BlockHarken 220 $53.95
  9. 9 29mm Cheek BlockHarken 350 $18.95
  10. 10 29mm Block — Swivel, BecketHarken 341 $33.95
  11. 11 29mm BlockHarken 348 $17.95

Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.

Go fast

Lightning tuning guide

Lightning tuning revolves around mast butt position, headstay length (or rake), upper and lower shroud tension and deck blocking for prebend, with the backstay, bridle and jib wire used on the water. North's M-5 system and the Quantum and VSP guides change blocking and lower tension with the wind (counting turns worked out in a dry run), while North's MF-2 system sets them once; North quotes forestay and lower readings on a Loos PT-1, while Quantum and VSP use pounds with Loos Model A equivalents that don't agree with each other for the lowers, so don't mix gauge numbers between guides.

North Sails — Lightning Tuning Guide (M-5 and MF-2 systems) Undated web page (current)

Written for
Mains M-5 and MF-2; jibs 5-A+, V17+, JF-2 and RJF; spinnaker
Tension gauge
Black Loos PT-1 for forestay and lowers; uppers and MF-2 lowers given in pounds
How it’s measured
50 ft tape, black spring-loaded PT-1 gauge (now used for both systems) and marker. Headstay length is measured from a tape mark on the headstay (level with the top of the mast band at the gooseneck) to the stem/deck intersection. Mast straightness: tape on the jib halyard to the chine below each upper chainplate, within 1/4″. MF-2 rake: relaxed rig, no jib, tape from the masthead to the transom/rear-deck intersection.
Source
North Sails, Undated web page (current)

Base setup

Mast butt, M-5
Maximum forward; aft edge 21 5/8″ forward of the centreboard pin
Mast butt, MF-2 and Allen
Maximum forward
Mast butt, Nickels (after hull 15200 and older)
Move aft one hole in the channel
Mast butt, Carson and Lippincott
20 1/4″ forward of the pin
Mast butt, prebend trouble or uppers further aft
Move aft 3/8″ to 5/8″
Headstay mark-to-deck, M-5
Nickels 44.5″; Allen 45″; new Nickels 45″
Headstay mark-to-deck, MF-2
Nickels 44″; Allen 44.5″; new Nickels 44.5″
M-5 uppers
Class maximum, 250 lb; lowers very loose to start; mast straight within 1/4″ each side (tape from jib halyard to the chine below the upper chainplate)
M-5 datum
Mast leaned fully back on the forestay with no shrouds or blocks = 0; mark 3/4″, 1″, 1 1/4″ and 1 1/2″ forward of it
M-5 base (2 on rail, starting to hike)
Block behind the mast to 1 1/4″ forward of datum; backstay on until the forestay reads 7 on the PT-1; lowers 11 on the PT-1, equal both sides
MF-2 initial
Uppers 250 lb, lowers about 80 lb (deliberately different from the class maximum)
MF-2 prebend
Push the mast forward in the partners and block behind it until lowers read about 250–300 lb; target 1 3/4″ to 2″ positive prebend at the spreaders (halyard-to-mast about 1 3/4″). Typical: 1/2″ block in front of the mast on new Allen/new Nickels. Lower target 300 lb (Allen, newer Nickels) or 250 lb (older Nickels, uppers aft). Uppers then drop to 160–190 lb; don't retighten above 190 lb.
MF-2 rake
Allen and newer Nickels 26′7″; older Nickels 26′6″; Lippincott/Carson 26′3″ to 26′4″. If more than 1/2″ too far forward, pull a 1/4″ block from behind the mast, retension lowers to 250 lb and recheck prebend.
MF-2 rake change
Pull the backstay until forestay slop is just gone: target 3″ to 4″ change. Over 4″: pull a small block from behind the mast and retension lowers to 250–300 lb. Under 3″: add a small block and ease lowers.

M-5 tuning matrix (lowers on Loos PT-1; headstay set to 7 on PT-1 with the backstay)

Wind / crewTurns on lowersMast blocking (forward of datum)Lowers PT-1Turns from base
0–5 "drifter"−11 1/2″Varies−2
Light (−2 in boat)−11 1/4″Varies−1
2 on rail, starting to hike (base)Base1 1/4″110
3 up, fully hiking11 1/4″181
Fully hiking, backstay coming on11 1/4″202
Depowering0.51 1/8″202.5
Maximum depowering1 (or 1.5)1″213.5 (or 4)
Main starting to luff1.53/4″285

Jib sheet trim

ConditionSetting
8–12 mph, flat water (5-A+, JF-2)Top batten 2–3″ inside the spreader tip (V17+ slightly tighter)
Below 8 mph, accelerating, out of tacksEase until the top batten is even with or past the spreader end
Extremely lightHold the clew up so the top batten is 1″ outboard of the spreader tip
Above 15 mphEase so the batten is 1″ or more past the spreader end

Bridle height

ConditionHeight
Light airRaised so the bridle block nearly meets the boom-end block when trimmed
Medium, above 6–8 mph11–12″ above deck
Heavy9″ above deck
Non-adjustable bridle11″ off deck

Trim by condition

Blocking and lowers (M-5)
They work together: light air uses forward blocking and eased lowers to prebend; more wind uses aft blocking and tighter lowers to stiffen the mast, with backstay to depower.
MF-2 lateral check
Sight up and adjust opposing lowers; recheck upwind in 8–10 mph. Above 10–12 mph a slight leeward sag above the spreaders is normal. Blocks and lowers then stay put until unstepping.
Jib halyard
5-A+ and V17+: luff wire as tight as the forestay with no sag between snaps. JF-2 and RJF: luff slightly tighter than the forestay with a slight snake between snaps; about 2 1/2″ of adjustment light to heavy.
Jib cloth
Slight luff wrinkles in light air; barely removed in heavy air; slightly past that in very heavy air.
Jib head lashing
Adjust the head lashing so the jib skirt lies on the deck for roughly 1 1/2–2″ and the tack sits no more than 3 1/2″ off the deck; re-tie or tape the lashing afterwards.
Jib lead
Sheet extends the trim line near the clew; move up to 2″ aft when overpowered. Tape rings on the spreaders 2″ and 4″ from the tips as references; the leech telltale must always flow.
Outhaul
Shelf-foot seam on the boom when overpowered; 1–2″ off in light air; downwind ease until the shelf opens (clew about 3″ in from the band).
Cunningham
MF-2 light air: slack with about 8″ wrinkles. M-5 light air: wrinkles only below the spreader window. Medium: wrinkles just below the spreader window. Heavy: pull hard to hold draft as the backstay goes on.
Backstay
Basic setting takes out slop; much more once everyone hikes; ease for waves or lulls. Ideal: overbend wrinkles just below the spreader window and halfway back on the boom.
Traveller
Centred in light to medium air; ease to leeward only after the outhaul is full and some backstay is on.
Mainsheet
Top batten parallel to the boom (sighted from below); 10–15° outboard in light air, chop or out of tacks; drifting, parallel to centreline with the boom up to 18″ to leeward. MF-2 in heavy or puffy air: vang so the top batten is 10° outboard and use the sheet like a traveller.
Spinnaker
About 6″ of luff curl; halyard eased about 6″ off the mast; clews even; pole nearly perpendicular to the wind.
  • The M-5 matrix has two turn columns (turns for that step and cumulative turns from base); both reproduced as published.
  • No spreader, jumper or centreboard settings are given.

Vermont Sailing Partners — Lightning Tuning Guide Undated, "constantly updated" web page (Bill Fastiggi)

Written for
VSP Lightning main and jib
Tension gauge
Loos Model A (pounds with gauge readings)
How it’s measured
Shroud tension with the backstay disconnected and the mast blocks removed. Headstay length from a tape mark at the top of the mast band to the forward edge of the bow deck. Jib lead measured from the forward edge of the bow, over the splash rail, to the jib track.
Source
Vermont Sailing Partners, Undated, "constantly updated" web page (Bill Fastiggi)

Base setup

Mast butt
Maximum forward; aft edge of the mast 21 7/16″ from the forward edge of the centreboard pin
Headstay length
44.5″ (Nickels) or 45″ (Allen); fine-tune so the boom is parallel to the deck
Uppers
250 lb = 29 on Loos Model A
Lowers
Nickels 120 lb = 15; Allen 170 lb = 21 (Nickels 15300 and newer use the Allen number)
Blocking marks
Neutral mark in the gate plus marks 7/8″, 1 1/4″ and 1 1/2″ forward

Dry run (blocking and lowers, pounds; Allen values in brackets)

SettingPrebendLowers (lb)Notes
Heavy air: block to 7/8″~1 1/2″~250 (~300)Uppers drop slightly
Medium air: block to 1 1/4″~1 1/2″250 (300)Author's boat: 2 full turns off lowers; extra forestay ~2″
Light air: block to 1 1/2″~3 1/2″ extra forestay200 (250)Author's boat: 3 full turns off each lower

Prebend and lower tension by wind (pounds; Allen in brackets)

Wind (mph)Prebend blockingLowers (lb)Turns from neutral
0–51 1/2″200 (250)Not listed
6–161 1/4″250 (300)Not listed
17+7/8″250 (300)0

Jib lead (bow to track)

Wind (mph)Lead
0–797″
8–1598″
16–2099″
20+100″+

Trim by condition

Jib sheet
Light air: top batten at the spreader tip, up to 4″ outboard in light spotty air (1–2″ outside in light chop). Medium: about 2″ inside the tip, never more than 3–4″ in. Over 20 mph: outside the tip, out to about 4″; leech telltale streaming 90–100%.
Jib wire
Tighter than the headstay in all conditions; in light air up to 3–4″ tighter; pull harder if pointing suffers or the luff bounces.
Jib cunningham
Remove about 90% of the snap wrinkles in light to moderate air, all of them from about 15 mph.
Bridle
Boom on centreline to 10 mph, then drop 1–2″ at a time; earlier in chop. Height so the sheet is 1/2–1″ short of two-blocked at the desired trim.
Top telltale
Stalls about 40% in light air, at most 60% in medium; streams most of the time above 16 mph.
Backstay
Light pull in light/medium air; first depowering control in breeze; more in smooth water, drop the bridle earlier in chop.
Main cunningham / outhaul
Remove about 90% of luff wrinkles; outhaul so the shelf foot just comes out upwind, slightly eased for power in medium breeze, tighter as wind builds (don't over-tighten).
Vang / leech line
Vang tight upwind in breeze, otherwise just slack removed; ease before bearing off. Leech line off until the leech flutters.
  • Model A readings conflict between guides: VSP gives 120 lb Nickels lowers as 15 on a Loos Model A (and 170 lb Allen lowers as 21), while Quantum's 2007 guide gives the same 120 lb as 13 on the same gauge model; both give 250 lb uppers as 29. Neither guide states the lower-shroud wire size, so the conflict can't be settled from the published guides. Set lowers by the pound figure and check against your own gauge's conversion chart.
  • The page is undated and says recent changes are marked in red.

Quantum Sails — How to Win in a Lightning 2007 (Quantum Newport; Randy and Bill Shore)

Written for
Quantum (Shore) Lightning sails, including the A.P. jib and A.P. mainsail
Tension gauge
Loos Model A (pounds with gauge readings)
How it’s measured
Mast butt from the front of the centreboard pin to the aft edge of the mast at the bottom. Shroud tension with backstay disconnected and blocks removed. Headstay: tape mark at the top of the mast band, measured to the forward edge of the deck at the bow. Rake: tape on the main halyard to the top centre of the transom with moderate tension.
Source
Quantum Sails, 2007 (Quantum Newport; Randy and Bill Shore)

Base setup

Mast butt (Nickels, Allen post-1985)
Maximum forward, 21 7/16″
Mast butt, other builders
Lippincott 20 3/4″; Carson 20 3/4″; Nickels 21 7/16″; Allen pre-11100 20 3/4″; Allen post-11100 21 7/16″; Nickels & Holman 20 3/4″; Mueller 20 3/4″
Shroud tension
Uppers 250 lb (29 on Loos Model A); lowers 120 lb (13 on Loos Model A)
Headstay length
44 1/2″ (neutral position); rake check 26′3″ for Allen boats that vary
Headstay lengths by builder
Lippincott 43 1/2″; Carson 43 1/2″; Nickels 44 1/2″; Allen pre-11100 42 1/2″; Allen post-11100 44″; Nickels & Holman 42 1/2″; Mueller 43 1/2″
Blocking marks
Neutral line plus marks 7/8″, 1 1/4″ and 1 1/2″ forward; dry-run the settings in the parking lot with the backstay off and count turns

Mast prebend (blocking) and lower shroud tension (pounds); 6–20 is the base setting

Wind (mph)Prebend (in)Lowers (lb)
0–51.5200
6–20 (base)1.25250
20+0.875250

Jib lead (bow, over the splash rail, to the track)

Wind (mph)0–1515–2020+
Lead position (in)96–9898–100100+

Trim by condition

Dry run
Block to 7/8″: lowers rise to about 250 lb. Block to 1 1/4″: count turns to bring lowers back to 250 lb. Block to 1 1/2″: count turns to bring lowers back to 200 lb. Record the turns.
Jib sheet
Light air: leech telltale streaming 90–100%, top batten from the spreader tip to 4″ outboard. Medium: telltale streaming 85%, top batten at most 4″ inside the tip. Heavy: outside the tip except in lulls, up to 4″ out over 20 mph.
Jib lead
Set so the luff telltales break evenly; Quantum likes the top one breaking just first.
Jib wire
Tensioned so the headstay just goes slack inside the snaps.
Cunninghams
Jib and main: remove 90% of the wrinkles in light to moderate air, all of them when it's consistently 15 mph+.
Mainsheet / bridle
Top batten parallel to the boom except when twisting off in high winds. Boom on centreline to 13 mph, then drop the bridle 1–2″ at a time; later in smooth water. Bridle height leaves the sheet 1/2–1″ short of two-blocked. Top telltale stalls about 40% light, at most 60% medium, streams above 16 mph.
Backstay
Slightly on in light air; first depowering control; more in smooth water.
Outhaul / vang / leech line
Shelf foot just out upwind (don't over-tighten the A.P. main); vang tight upwind in breeze; leech line only to stop flutter. Downwind: vang so the top batten is parallel to the boom.
  • Hosted on Quantum's own documents page (still the only Lightning document linked from Quantum's current Lightning page); the PDF is dated 2007 and may predate Quantum's current Lightning sails.
  • Its 120 lb = 13 (Model A) lower reading differs from VSP's 120 lb = 15; see the VSP entry.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Lightning resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Lightning by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current Lightning class rules before changing equipment, and ask your class measurer if a part is not original equipment.