One-design race shop · Dinghy

ILCA / Laser Race Shop

Everything you need to prepare, compete, and win.

Shopping for

ILCA / Laser

  • 55 verified parts
  • 11 brands
  • Fit checked Nov 2026

Fit verified for ILCA / Laser

All ILCA / Laser equipment

55 parts

Can’t find a part for your ILCA / Laser? Request a ILCA / Laser part

Ready to install

ILCA / Laser running rigging

Sheets, halyards and control lines whose length and diameter we have matched to the ILCA / Laser specification.

Official Harken dealer

ILCA / Laser deck layout

LOA
4.23 m (14 ft)
Beam
1.42 m (4.6 ft)
Draft
0.9 m (2.9 ft)
Mast Height
5.9 m (19 ft)
Sail Area
7.06 sq m (76 sq ft)
Weight
59 kg (130 lb)

Vang

    Deck layout

    Deck layout — Harken layout for the ILCA / Laser
    Drawing: Harken
    1. 1 Micro Cam-Matic® CleatHarken 468 $36.95
    2. 2 Micro Cam-Matic® CleatHarken 468 $36.95
    3. 3 18mm Fly Soft-Attach BlockHarken 2698 $25.95
    4. 4 18mm Fly Soft-Attach Double BlockHarken 2158 $42.95
    5. 6 18mm Fly Soft-Attach BlockHarken 2698 $25.95
    6. 7 18mm Fly Soft-Attach Double BlockHarken 2158 $42.95
    7. 8 16mm Forkhead BlockHarken 376 $24.95
    8. 9 16mm Forkhead BlockHarken 376 $24.95
    9. 10 Micro Cam-Matic® CleatHarken 468 $36.95
    10. 12 57mm Ratchet Block — SwivelHarken 2135 $86.95

    Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.

    Go fast

    ILCA / Laser tuning guide

    The ILCA has a fixed, unstayed rig and class-supplied sails, so tuning is about the controls: cunningham, vang, outhaul, traveller and mainsheet (block-to-block) by wind, plus body position. Guides measure the outhaul differently (depth at mid-foot in cm, hand spans, or clew distance from the boom end), so compare like with like.

    World Sailing — Technical Course for Coaches Level 3 — ILCA Trim PDF uploaded October 2025

    Written for
    ILCA sail (rig size not specified)
    Tension gauge
    Not applicable
    How it’s measured
    Outhaul as a depth in cm 'in the center of the sail' (read here as depth off the boom at mid-foot); mainsheet as the gap between the blocks; cunningham by luff tension.
    Source
    World Sailing, PDF uploaded October 2025

    Base setup

    Control map
    Top third of the sail = cunningham; middle third = vang and mainsheet; lower third = outhaul

    Upwind settings by wind

    WindObjectiveCunninghamVang and mainsheetOuthaul (depth 'in the center of the sail')
    Very lightAverage depth with open leechVery low pressureKeep the sheet at 20–30 cm, then pull the vang 'plus 2 cm more' (as printed)10 cm
    LightDeep sail, especially with wavesVery low pressureSheet 0–20 from block to block, no vang10–15 cm
    MediumDeep, powerful sailJust the wrinklesBlock to block, a little vang10–15 cm
    StrongDepower starting from the topEye touches the gooseneckBlock to block, ease in the gusts; maximum vang5–10 cm
    Very strongVery flat sail, easing the mainsheetMaximum tensionAverage vang; keep the boat flat with the mainsheetNo depth

    Trim by condition

    Cunningham
    Pulling it moves maximum depth forward and opens the upper leech: faster acceleration, lighter helm and easier in waves, but less pointing and top speed, and too little power in medium air. Easing does the opposite.
    Vang
    Bends the mast from the bottom, opens the whole leech and lightens the helm in breeze; in light air it gives shape and pointing. Easing it in medium air adds power.
    Outhaul
    Ease in light air and big waves for power to climb the waves; set it wrong and both pointing and speed suffer.
    Reaching and downwind
    Keep playing the mainsheet with every change in pressure; set the vang loose enough that the top batten is more open than the lower ones and re-trim it for big pressure changes.
    Body position
    Light: forward by the daggerboard, aft foot over the strap to leeward, minimal movement; move aft as the wind builds. Strong: never cleat, legs straight, chest high, steer with the body through the waves.
    • Coach-education slides rather than a sailmaker guide; wind bands are descriptive (no knot ranges).
    • The very-light sheet figure (20–30 cm) doesn't say what it is measured between, and the light-air '0–20 from block to block' has no unit; the slides use cm elsewhere. 'Pull the vang plus 2 cm more' is as printed.

    Kanata Sailing Club — Basic Laser Tuning 2014 PDF

    Written for
    Laser (rig size not specified)
    Tension gauge
    Not applicable
    How it’s measured
    Traveller height off the deck at its highest point; mainsheet as the gap between the traveller blocks with the sheet fully in; outhaul as the gap between boom and foot at the point of maximum draft.
    Source
    Kanata Sailing Club, 2014 PDF

    Settings by wind

    ControlLight (10 kn or less)Medium (10–15 kn)Heavy (15 kn or more)
    Traveller4–6″ off deck at its highest point; blocks no further inboard than the corner of the stern when fully sheetedSame, and ease the traveller as you get overpowered upwind6–8″ off deck; blocks outboard of the stern corner when fully sheeted
    Mainsheet upwind1–10″ between the blocks when fully sheeted, the gap shrinking as wind increases; don't oversheetBlocks touching, but ease as needed to keep the boat flatKeep the boat flat with the sheet once hiking isn't enough; blocks may be 18″ apart
    VangSheet to about 1″ between blocks, then take the slack out of the vang; tight enough that the boom doesn't rise with no sheet load; add vang as you get overpoweredAs lightVery tight; the boom visibly bends
    OuthaulOne hand span between boom and foot at the point of maximum draftClew about 3″ from the bullseye at the boom end; tighten as you get overpowered, ease slightly if there's lots of weather helm3–4″ between boom and foot at maximum draft under load; less if overpowered
    CunninghamJust snugTight enough to smooth wrinkles between tack and clew; more as you get overpoweredVery tight, grommet at or below the boom; ease on runs
    Crew close-hauledSlightly forward of the main block, slight leeward heelSlightly aft of the main blockCentred on the hiking strap
    Crew reachingSlightly aft of the main blockBody angled back; move back as the boat starts to planeAs far aft as possible, body angled out
    Crew runningAs far forward as possible with feet in the cockpit; heel to windward and hold the boom outStraddle the centreboard trunk, move aft as it planesAs far aft as possible; in death rolls hold position and steer into the roll

    Trim by condition

    Offwind sheet
    Ease until the sail luffs, then trim in slightly.
    Vang offwind
    Ease until the mast is straight (light/medium). In heavy air beware: with a tight vang the boom can hit the water and pivot the boat into a capsize.
    Death rolls
    Sheet in as the boat rolls to leeward and out as it rolls to windward.
    Outhaul offwind
    Don't loosen it offwind (medium-air advice).
    • A simple club handout, not a sailmaker guide.
    • The inch marks are garbled in the PDF's text layer; values are read as inches. The light and medium vang advice share one cell in the original.

    Rooster Sailing — Laser – My Mast Rake March 2021 blog article

    Written for
    Laser Standard and Radial (ILCA 7 / 6); 4.7 comments
    Tension gauge
    Not applicable
    How it’s measured
    Tape taped to the top of a straight standard lower mast, mast stepped, tape run to the back of the boat; read where the tape touches the aft deck. Radial sailors need to borrow a standard lower mast.
    Source
    Rooster Sailing, March 2021 blog article

    Base setup

    Author's preferred Radial rake
    About 3820 mm (his example boat read 3820 mm, perhaps 3818 mm allowing for the tape)
    Very aft rake
    3795 mm on his first Standard: great in light air, not competitive in medium or strong winds
    Upright limit
    Much more than 3830 mm and he couldn't get block-to-block; 3835 mm uncomfortable in a Radial (heavy helm); a 3860 mm charter boat at a Worlds had no power in the upper leech (he calls it 'a pig')
    Regional differences
    Australian boats had a 3830 mm rake (traditionally further forward than European boats), paired with bendy standard lower and stiff upper masts
    4.7 lower mast
    Should have 15° of bend; check it before choosing a rake preference

    Trim by condition

    Choosing spars
    Rake can't be adjusted, so match spars to it: a bendier lower mast suits a more upright (larger number) rake but needs a stiff upper mast; for the Radial he prefers a bendy lower and an upper mast of about 2.85 kg.
    Symptoms
    Rake too far forward: slow in light air, upper mast over-bent to reach block-to-block, more pitching and, oddly, more weather helm.
    • One sailor's opinion based on his own boats; builders keep rake within about a centimetre, so this is for checking and choosing equipment rather than adjusting.

    Settings are summarised from each sailmaker’s published guide (checked 2026-11-03). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

    Technical

    ILCA / Laser resource centre

    How we verify parts

    Fit verified
    Each part listed here was matched to the ILCA / Laser by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
    Class rules
    Fitting a part is not the same as it being legal for racing. Read the current ILCA / Laser class rules before changing equipment, and ask your class measurer if a part is not original equipment.