One-design race shop · Dinghy

Flying Scot Race Shop

Everything you need to prepare, compete, and win.

Shopping for

Flying Scot

  • 19 verified parts
  • 4 brands
  • Fit checked Nov 2026

Fit verified for Flying Scot

All Flying Scot equipment

19 parts

Can’t find a part for your Flying Scot? Request a Flying Scot part

Official Harken dealer

Flying Scot deck layout

Length Overall
19 ft (5.8 m)
Beam
6'9" ft (2.05 m)
Draft-Board Up
8 in (.2 m)
Draft-Board Down
48 in (1.2 m)
Mast Height
28 ft (8.6 m)
Sail Area, Main & Jib
191 sq. ft (17.65 sq. m)
Sail Area, Spinnaker
200 sq. ft ( 18.6 sq m)
All Up Weight
850 lb (386 kg)

Deck layout

Deck layout — Harken layout for the Flying Scot
Drawing: Harken
  1. 1 57mm Fiddle Block — SwivelHarken 2621 $66.95
  2. 3 57mm Block — Swivel BecketHarken 2601 $62.95
  3. 5 57mm Block — SwivelHarken 2600 $55.95
  4. 6 Standard Cam-Matic® Cleat - 150Harken 150 $44.95
  5. 7 Standard Cam-Matic® Cleat - 150Harken 150 $44.95
  6. 8 29mm Cheek BlockHarken 350 $18.95
  7. 9 29mm Block — Swivel, BecketHarken 341 $33.95
  8. 10 29mm BlockHarken 348 $17.95
  9. 13 29mm Cheek BlockHarken 350 $18.95
  10. 14 29mm BlockHarken 348 $17.95
  11. 15 29mm BlockHarken 348 $17.95
  12. 16 29mm BlockHarken 348 $17.95
  13. 17 Micro Cam-Matic® CleatHarken 468 $36.95
  14. 18 38mm Bullseye FairleadHarken 237 $6.95
  15. 19 Micro Carbo-Cam CleatHarken 471 $31.95
  16. 20 Standard Cam-Matic® Kit — Fast Release FairleadHarken 496 $66.95
  17. 21 57mm Ratchamatic® Block — SwivelHarken 2625 $121.95
  18. 22 Standard Cam Base — SwivelHarken 144 $180.95
  19. 23 57mm Ratchet Block — SwivelHarken 2135 $86.95
  20. 24 29mm Cheek BlockHarken 350 $18.95

Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.

Go fast

Flying Scot tuning guide

The Flying Scot is tuned once ashore (rake measured masthead to the transom/aft-deck joint, plus forestay or shroud tension) and then sailed with the cunningham, outhaul, vang, weather jib sheet and centreboard. Guides disagree on rig tension because North's Tight Rig jib wants about 240 lb while snug-rig set-ups want 80–120 lb (North 80–110 lb, Quantum about 100–120 lb), so match the guide to your jib; rake targets cluster between 28′3″ and 28′6″.

North Sails — Flying Scot Tuning Guide Rev. R03 (undated web page)

Written for
North main (shelf foot); Loose Rig, Snug Rig and Tight Rig jibs (the Tight Rig set-up only works with a jib cut for it); spinnaker
Tension gauge
Tension given in pounds; gauge model not named
How it’s measured
Aft rake: hoist a tape on the main halyard and hold it at the joint of the transom and rear deck, jib down. Slop = forward rake minus aft rake.
Source
North Sails, Rev. R03 (undated web page)

Base setup

Loose Rig: aft rake (jib down)
28′4″ to 28′5½″ (tape on the main halyard to the transom/rear-deck joint)
Loose Rig: slop
Push the mast forward until the shrouds stop it; forward minus aft measurement about 2–3″
Forestay adjuster
North fits a channel adjuster above deck at the joint of the forestay and the toggle wire to adjust rake and forestay length quickly
Tight Rig: shrouds and tension
Drop the shrouds as low as possible in the channel adjusters (bottom of the swage fork just above the chainplate); tension with the jib halyard to the bow plate, target 240 lb, set between 220 and 250 lb. Under 220 lb the headstay sags in medium air; over 250 lb can push the mast out of column in heavier air.
Tight Rig tensioning
A 3/8″ socket wrench in the halyard box (standard aluminium cranks may break); once set it doesn't need changing
Tight Rig: rake
Very close to 28′4″–28′5″; further forward than 28′5½″ gives too light a helm; more rake than 28′3″ gives too much weather helm
Snug Rig jib
Tuned like the Tight Rig: rake close to 28′4″–28′5″; rig tension 80–110 lb measured on the forestay
Toggle
With the Snug/Tight set-up the toggle is no longer used to set rake, jib luff tension or slop; the forestay carries the rig load and the jib halyard only sets cloth tension
Rudder blade
Forward lower tip about 5″ aft of a line tangent to the blade's forward edge, parallel to the rudder head's forward edge (factory-like angle)
Crew weight
Target 360–450 lb

Outhaul (gap between boom side and shelf-foot seam)

ConditionSetting
Upwind, normal1½–2″ (3.8–5.1 cm)
Light air or choppy seas2″
Downwind3–4″
Heavy airTighter, closing the shelf
Above 18 mphHard crease tack to clew

Trim by condition

Mainsheet
Upper batten parallel to the boom normally; about 5° outboard in light air or chop. Drifting: upper batten parallel to centreline (boom about 2′/61 cm off centreline). Heavy air with vang: about 5° outboard of parallel to the boom. Keep the sheet in hand and ease quickly in puffs.
Vang
Above 15 mph use heavy vang so mast and boom bend to flatten the main; in heavy breeze the boom may deflect nearly 3–4″ (7.6–10.2 cm). Ease it before rounding the windward mark. Upwind in heavy air the upper batten should not go more than 5–10° past parallel to the boom (the sheet then works like a traveller). Downwind, set the upper batten slightly out from parallel so the top leech telltale flies; don't over-vang in light air or under-vang in breeze. Amount depends mainly on crew weight.
Cunningham / main halyard
A hint of horizontal wrinkles in the lower third of the luff; err loose.
Jib luff
Slight crow's feet off each snap with no sag between snaps; tighten until they disappear in heavy air.
Jib lead
Normally full forward; full aft when overpowered.
Jib sheets
Trim the leeward sheet until the foot is smooth; in light to moderate air trim the windward sheet until the clew sits over the middle of the seat. At speed the top batten lies nearly straight back; in chop or lulls ease so it angles 15–20° outboard; in heavy air the windward sheet is well eased or off. Tie an overhand knot about 6″ from the clew (2:1 block also about 6″ from the clew).
Centreboard
Fully down upwind; in heavy air roll back 1–2″ from the bottom of the hump if it balances better; near survival lower only until the rollers touch the flat at the bottom of the hump. Downwind raise to balance the helm, up to about ¾ on a breezy reach.
Spinnaker
6–12″ of luff curl; clews even via pole height (or centre seam parallel to the mast); ease the halyard so the head sits 6″ off the mast; sit well aft running in breeze.
Steering (Snug/Tight Rig jibs)
Light to medium air: steer like the Loose Rig jib (windward telltale may stall when pointing, never sail below the leeward telltale streaming). In breeze the windward telltale will usually stall and the luff may break back as far as 12″; that's acceptable in the upper groove.
  • The rake section is split: the Loose Rig text gives 28′4″–28′5½″ with 2–3″ slop; the Tight/Snug Rig text gives 28′4″–28′5″ and the 28′3″/28′5½″ limits. Read rake numbers as tape lengths (shorter = more rake).
  • Mixes mph wind references with no knot conversions.

Ullman Sails — Flying Scot Racing Guide and Flying Scot Sail Trim Chart 2014 (year from the hosted file names; the PDFs themselves are undated)

Written for
Ullman Flying Scot main (with window) and jib (top-batten stripe and telltale), spinnaker
Tension gauge
Not named (forestay tension in pounds)
How it’s measured
Rake: metal tape on the main halyard shackle hoisted until nearly two-blocked (swage sleeve just touching the sheave, shackle at a fair angle), measured to the hump in the middle of the aft deck where it turns down to the transom. Tune once and mark the pin settings.
Source
Ullman Sails, 2014 (year from the hosted file names; the PDFs themselves are undated)

Base setup

Rake
Within an inch of 28′5″
Forestay tension
About 100 lb, ±10 lb

Sail Trim Chart (wind in knots)

Control0–45–1011–1617+
Mainsail luff tension12″ wrinkles6″ wrinklesNo wrinklesTight
Mainsheet tensionTop batten parallel with centre of boatTop batten parallel with boomTop batten opens 5–10°Top batten open 10+°
Outhaul3–4″2–3″1″Tight
Upwind vang tensionLooseLooseMediumMax tight
Jib luff tensionWrinklesWrinklesSmoothSmooth
Jib leadsBackForwardMiddleBack
Windward sheetSlightly onMiddle of seatSlightly onOff
Jib sheet tension (top batten position)Parallel to centre of boat or slightly openParallel or slightly hookedParallel to slightly openOpen enough to keep boat moving and flat

Trim by condition

Main, 0–4 kn
Cunningham off and halyard loose enough for 12″ horizontal wrinkles; ease until the aft third of the top batten is parallel to centreline (boom often to the transom corner); outhaul eased about 3–4″.
Main, 5–10 kn
Sail flat and powered: vang off, cunningham loose, outhaul about 2–3″ from max, top batten parallel to the boom, everyone hiking.
Main, 11–16 kn
Flatten progressively: cunningham on, outhaul to about 1″ from max, vang on as soon as overpowered and ease the sheet in puffs (sheet acts like a traveller); top batten parallel in lulls, open 5–10° in puffs.
Main, 17+ kn
Vang very tight (boom may bend as much as 3″) and ease it before bearing away; leech open 10° or more; cunningham all on; outhaul full on only in very heavy air or flat water.
Jib
Halyard set for crow's feet off each snap. Weather-sheet the lazy sheet to bring the clew over the middle of the seat (not in a drift); keep the top-batten telltale flowing. 11–16 kn: same, ease slightly in big puffs and chop. 17+ kn: weather sheet slack, top batten slightly open.
Downwind
Vang until the top batten is parallel to the boom; when running, main out to the shrouds. Jib stays up except in very light air, where dropping it can help the spinnaker.
Spinnaker
Halyard 6″ below full hoist (a double figure-eight stopper is common); pole height so the curl appears mid-luff; guy keeps the pole perpendicular to the wind; sheet on the edge of curling.
Crew position
Upwind sit close together; medium air skipper's aft hip at the mainsheet cleat, heavy air at the back of the centreboard trunk. More than 10–15° of heel is undesirable.
  • Ullman's own archive copies (oldarchive.ullmansails.com) return HTTP 401, so the links are to copies hosted by canadianboating.ca. The trim chart is a separate one-page file: https://canadianboating.ca/wp-content/uploads/2020/05/Ullman-Sails-Flying-Scot-Tuning-Chart-2014.pdf
  • The chart's 'Jib leads' row (back in 0–4, forward in 5–10) and 'Windward sheet' row are reproduced exactly as printed.

Quantum Sails — Flying Scot Tuning Guide (Snug Rig) 2007 (file title 'Flying Scot Tuning Guide - 2007'; Quantum Toledo, Skip Dieball)

Written for
Quantum Flying Scot main (tapered battens), jib, spinnaker
Tension gauge
Loos tension gauge on the forestay (model not named)
How it’s measured
Rake: tape hoisted as high as possible on the main halyard, measured from the masthead to the top edge of the transom (top of the hump). Forestay tension measured on the trailer without sails.
Source
Quantum Sails, 2007 (file title 'Flying Scot Tuning Guide - 2007'; Quantum Toledo, Skip Dieball)

Base setup

Rake
Class standard roughly 28′5″; with Quantum sails some boats are best raked slightly more, 28′3″ to 28′4″. Rake forward for acceleration (chop, tacking duels), back to point; adjust in ½–1″ steps, mainly through tension, keeping rig tension constant.
Forestay tension
About 100 lb all-round; less experienced sailors about 120 lb for a wider groove
Crew weight
385–485 lb works well; three people totalling 435 lb ideal

Trim by condition

Battens
Softer tapered battens for light air, chop or heavy crews (softest at the top); change to stiffer ones from about 13 kn (whitecaps), top batten first. Insert thin end first.
Outhaul
Smooth shape upwind in moderate air; hard crease along the foot in flat water or strong wind; ease in light air, chop or reaching.
Cunningham
Seldom needed below 13 kn; small luff wrinkles are fine.
Vang
Light to moderate air: set so that when the main is eased the boom rises a couple of inches and the upper batten falls off up to 8° before the boom swings out. More vang in heavier air to bend the mast and help forestay tension.
Jib
Bottom batten straight back parallel to centreline; leech telltale always streaming; windward telltale lifting slightly every 5–6 seconds in max-point mode.
Main, beating
Upper batten parallel to the boom with the top telltale stalled 50–70% of the time; when footing, in puffs or light air ease so the batten falls off up to 10°; when pinching, hook it up to 10° for a couple of seconds.
Spinnaker
Pole perpendicular to the wind; on a reach pull it back an extra 6–10″ if trim holds; ease the halyard 6–8″; twings above 5 kn.
Centreboard
In a blow roll the board back or lift it slightly; raise to neutral helm reaching, half up or more running; err on more board upwind.
Steering
Tack about 5° wide, build speed, then sheet the last couple of inches.
  • Six-page Quantum Toledo guide (PDF metadata: author Skip Dieball, June 2008).

Quantum Sails — Flying Scot Class Tuning Guide – quick set-up guide (Loose Rig) 2007, Quantum San Diego

Written for
Quantum Flying Scot main (shelf foot, long leech), jib, spinnaker
Tension gauge
Not stated
How it’s measured
Mast rake with the mast aft, then again with it pulled forward to check slop; then check side-to-side measurements.
Source
Quantum Sails, 2007, Quantum San Diego

Base setup

Mast rake
28′3″ to 28′6″ with the mast aft
Slop
Difference between mast-aft and mast-forward measurements 3″ to 5″

Trim by condition

Main cunningham
Almost never adjusted; halyard fully up with slight luff wrinkles; a little cunningham in stronger winds.
Main outhaul
Over 8 kn pull tight to close the shelf; in lighter air or real chop a little fullness helps up to about 12 kn; reaching and running ease until the shelf just opens.
Mainsheet
Top batten parallel or just hooking to weather of the boom.
Jib halyard
A bit more than crow's feet off the snaps; tighten as the wind builds.
Jib leads
Most of the time all the way forward.
Jib sheets
Tie a knot about 10″ below the clew attachment so the sheets split 10″ from the sail; under-sheet first, pull the weather sheet until the clew is about mid-seat, then sheet the rest of the way.
Centreboard
Upwind move the rollers back as needed to balance helm; reaching as high as possible without slipping; running all the way up.
  • Despite the file name, this short guide gives no rig tension number.

Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.

Technical

Flying Scot resource centre

How we verify parts

Fit verified
Each part listed here was matched to the Flying Scot by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
Class rules
Fitting a part is not the same as it being legal for racing. Read the current Flying Scot class rules before changing equipment, and ask your class measurer if a part is not original equipment.