One-design race shop · Keelboat
Dragon Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Dragon
All Dragon equipment
29 parts
Fit verified for Dragon
Vakaros
Vakaros Atlas Edge (High-Performance GPS Sailing Instrument)
Part # VAK-VK-EDGE
$749.00
$775.75Fit verified for Dragon
Boomkicker
Boomkicker Spares – Top Clamp Plate – For K0800 & K1000
Part # BOOK1020-2
$20.13
$21.96Fit verified for Dragon
Boomkicker
Boomkicker Spares – Mast Fitting Assembly – For K0800 & K1000
Part # BOOM1000
$72.88
$79.50Fit verified for Dragon
Boomkicker
Boomkicker Spares – Extension Clamp Assembly – For K0800 & K1000
Part # BOOK1080
$70.55
$76.96Fit verified for Dragon
Boomkicker
Boomkicker Spares – Jaw Extension – For K0800 & K1000
Part # BOOK1040
$22.88
$24.96Fit verified for Dragon
Nautalytics
Nautalytics Bulkhead Mount Compass (Digital Compass)
Part # NTL-BULKHEADMOUNT
$400.00
Fit verified for Dragon
Boomkicker
Boomkicker Spares – Fastener Pack (Screws, Drill, Tap, Hex Key) – For K0800 & K1000
Part # BOOM1060
$25.63
$27.96Fit verified for Dragon
Boomkicker
Boomkicker Spares – Boom Roll‑Stop Fitting Assembly – For K0800 & K1000
Part # BOOM1051
$105.00
$119.96Fit verified for Dragon
Boomkicker
Boomkicker Spares – Mast Bracket for K0800 & K1000
Part # BOOM1020
$23.80
$25.96Fit verified for Dragon
Boomkicker
Boomkicker Spares – Boom Track Slider – For K0800/K1000
Part # BOOB1060
$27.46
$29.96Fit verified for Dragon
Boomkicker
Boomkicker Spares – Bottom Clamp Plate – For K0800 & K1000
Part # BOOK1020-1
$20.13
$21.96Fit verified for Dragon
Ritchie
Ritchie Bracket Mount RitchieSport X-10W-M Compass (White Housing/Black Card)
Part # RIT-X-10W-M
$48.99
Fit verified for Dragon
Boomkicker
Boomkicker Spares – Mast Swivel – For K0800 & K1000
Part # BOOM1010
$23.80
$25.96Fit verified for Dragon
Boomkicker
Boomkicker Spares – Boom Track 267 mm (10.5 in) – For K0800 and K1000
Part # BOOB1080
$50.38
$54.96Fit verified for Dragon
Ritchie
Ritchie Bracket Mount RitchieSport X-10B-M Compass (Black Housing/Black Card)
Part # RIT-X-10B-M
$51.99
Fit verified for Dragon
Ritchie
Ritchie X-11Y SportAbout Handheld Compass - Yellow
Part # rit-x-11y
$59.99
Fit verified for Dragon
Velocitek
Velocitek Mast Bracket for Prostart or SpeedPuck
Part # VELPROMMB
$69.00
Fit verified for Dragon
Ronstan
Ronstan CleartStart Analogue Sailing Watch, 43mm - Unisex (Black/Red)
Part # RSGRF4056
$169.96
$199.95Fit verified for Dragon
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for Dragon
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for Dragon
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for Dragon
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for Dragon
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for Dragon
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95Fit verified for Dragon
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95
No Dragon parts match these filters.
Can’t find a part for your Dragon? Request a Dragon part
Go fast
Dragon tuning guide
Dragon tuning starts with forestay length (rake), mast and shroud positions measured from the station 4 line, then shroud tensions by wind, with running backstays, the mast ram and jumpers used to change gear on the water. Each guide is written for its own sails and mast builder, and the gauges differ (Loos PT-2M for North, Fritz and Petticrows; Loos Model B for Høj Jensen, which also reads the uppers with the plastic cover on), so read every tension number with the gauge that guide names.
North Sails — Dragon Tuning Guide Undated web guide (compiled by Jørgen Schönherr, Poul Richard Høj Jensen and Theis Palm)
- Written for
- Mainsail A-7+ (standard Petticrow and BB masts); LM-2 (stiff Petticrow mast, light and medium) and A-10 (stiff Petticrow mast, heavy); genoas MG-15 / MJ-8 (light, medium) and HG-15 / MJ-8H (heavy); spinnaker CD-5 or R-5
- Tension gauge
- Loos PT-2M (the guide spells it "Loose Gauge" in places)
- How it’s measured
- Mark the uppers and forestay at the black band, 80 cm above deck, with the wires pulled up along the mast. Rake is measured along the forestay from that mark down to the deck. Mast and shroud positions are measured from the midpoint of the station 4 line to the front of the mast (excluding the pole track). Upper-shroud tensions are read without the plastic cover; cut it about 1.2 m above deck.
- Source
- North Sails, Undated web guide (compiled by Jørgen Schönherr, Poul Richard Høj Jensen and Theis Palm)
Base setup
- Forestay position
- At the class-maximum distance from the front of the mast; the page prints this as "1,86 cm" (presumably 1.86 m)
- Mast position (station 4 to mast front)
- 83,0 cm (Petticrow) / 81,5 cm (BB)
- Upper shroud position
- 83 cm from station 4 at all times; 80 cm for light crews. Light crews (220–240 kg) leave the shrouds one hole forward.
- Lower shroud position
- The hole just behind the uppers (approx. 3 cm), so the lowers don't hold the mast back when running
- Centring
- Measure from the 80 cm marks on the uppers to the deck; equal both sides, mast not distorted at deck level
- Forestay tension / runner marks
- Rig in the strong-wind position (uppers 20, lowers 8). With the gauge on the forestay near the black mark, pull each runner until it reads 30 and tape the runner where it exits the deck (mark #1, the maximum runner setting). Eased until the forestay is just tight, that tape should sit about 15 cm above deck.
- Jumpers
- Tighten with the permanent backstay until equal both sides and the mast is completely straight
- Lowers in breeze
- Mast straight up to 20–22 kn; above that tighten until the mast drops 5–10 cm to leeward where the forestay meets the mast (depends on crew weight)
On the water tuning (Loos PT-2M)
| Setting | Light 0–5 kn | Medium 6–16 kn | Heavy 17+ kn |
|---|---|---|---|
| Mast rake | 123,5 cm (Petticrow) / 120,0 cm (BB) | 122,5 cm (Petticrow) / 120,0 cm (BB) | 122,5 cm (Petticrow) / 120,0 cm (BB) |
| Mast ram | Mast 1,5 cm forward at deck level | Mast neutral | Mast 2,5 cm forward at deck level |
| Mast position (from station 4) | 83,0 cm (Petticrow) / 81,5 cm (BB) | 83,0 cm (Petticrow) / 81,5 cm (BB) | 83,0 cm (Petticrow) / 81,5 cm (BB) |
| Jumpers | Adjustable: loose. Fixed: Loos 6 | Adjustable: mast straight. Fixed: Loos 6 | Adjustable: mast straight. Fixed: Loos 6 |
| Upper shrouds (no plastic) | Base 14 (std. Petticrow & BB) or 12 (stiff Petticrow) minus 1 turn | Base plus 1–2 turns | Base plus 3 turns |
| Lower shrouds | Mast bends 1 cm to leeward at spreader level | Mast straight | Mast straight plus 1–1½ turns so it bends to windward |
| Backstay | A little tension in very light air (to pre-bend the mast) | Just tight, so the masthead doesn't move in waves | Just tight, so the masthead doesn't move in waves |
| Runners | Slack to 15–16 cm above deck (mark #4) | 15–5 cm above deck (marks #3–#2) | 5–0 cm, maximum (mark #1) |
| Mainsheet | Light sheeting; upper telltales flying straight back | Top batten parallel to boom; upper telltales 20% on leeward side | Main flying nicely; top batten 2° twisted to leeward; telltales straight back |
| Traveller | To windward, boom on centreline | To windward, boom on centreline | Centred and up to 10 cm to leeward |
| Outhaul | 2,0 cm from black band | 1 cm from black band | All the way out to black band |
| Cunningham | Loose | Loose – just remove luff wrinkles | Just remove luff wrinkles |
| Boom vang | Loose; cleated ready for the run | Loose; cleated ready for the run | Loose; cleated ready for the run |
| Genoa sheet | Foot just touching the shroud at deck level | Foot touching 10 cm up the shroud | Foot touching 25 cm up the shroud |
| Genoa barberhauler | Mark #4 / 15 cm out of cuddy; leech 15–18 cm from spreader | Mark #2 / 9–10 cm out of cuddy; leech 5 cm from spreader | Mark #3 / 10–12 cm out of cuddy; leech 8 cm from spreader |
| Genoa halyard | Small luff wrinkles | Just remove luff wrinkles | Just remove luff wrinkles |
Trim by condition
- Pointing
- If you can't point, pull the mast back with the ram first; then try more mainsheet.
- Helm and flat sails in breeze
- Keep the helm light with the traveller; in heavy air the main should be flat along the boom, and in very heavy air the cunningham can be pulled hard to bring the draft forward.
- Vang off the wind
- On reaches and runs, tension the vang until the top batten lines up with the boom.
- Genoa halyard
- Don't over-stretch the luff.
- Sail choice
- Waves and sea state move the wind ranges in which each sail works best.
- Experiment
- Crew weight, balance, mast stiffness and local conditions all change the final set-up; use the guide as a start point.
- The guide is not dated on the page; the British Dragon Association magazine index lists a Jensen, Palm and Schönherr "Tuning Guide" from 2007 (the index warns its 2004–2010 dates may be a year off), which may be the same material – not confirmed.
- "1,86 cm" for the forestay distance is a typo in the source; the class J maximum is 186 cm (see Petticrows guide).
- The jumper row is laid out irregularly on the page; the reading above (adjustable jumpers loose then mast straight, fixed jumpers at 6 throughout) is the most consistent one.
- The 20 / 8 tensions in the forestay set-up step are a set-up position, not the on-the-water base (14 or 12).
- The table's heavy column starts at 17 kn, but the set-up text keeps the mast straight sideways up to 20–22 kn before tightening the lowers further.
- The old northsails.com/sailing/en/resources/dragon-tuning-guide address now redirects to the URL above.
Fritz Segel — The Dragon Tuning Manual Undated; the file name says V04 (no version or year is printed in the manual). Compiled by Vincent Hoesch from the experiences of Vincent Hoesch and Werner Fritz.
- Written for
- Fritz Dragon sails; the manual's sail section recommends main A1, genoas C-2VL (0–3 Bft), C-2V (0–6 Bft, all-round), C-2 (0–6 Bft, inland or long sea waves), C-2H (4–8 Bft) and spinnaker 9XL (0–8 Bft)
- Tension gauge
- Loos PT-2M; readings in LU (Loos units). 16 LU on the runner = about 4200 N (420 kp).
- How it’s measured
- All shroud, runner and forestay readings about 1450 mm above deck, with the plastic cover removed on the uppers. Shroud positions are measured from station 4 aft to the middle of each shroud. Wind in Beaufort; LW 0–1 Bft, MW I 1.5–2.5 Bft, MW II 3–4 Bft, HW/SW 4.5–8 Bft. Shroud tensions are set with both runners at 6 LU and the ram at zero.
- Source
- Fritz Segel, Undated; the file name says V04 (no version or year is printed in the manual). Compiled by Vincent Hoesch from the experiences of Vincent Hoesch and Werner Fritz.
Base setup
- Mast rake
- 1215 mm for all boats (forestay marked level with a mark 790 mm above deck, then measured along the forestay to the deck with 25 LU on the forestay)
- Shroud positions behind station 4
- Petticrows: uppers 790–800 mm, lowers 820–830 mm; Børresen: uppers 790–810, lowers 820–840; Glas: uppers 790–800, lowers 820–830
- Mast mark / J
- Aft edge of the 50 mm mast marks 820–840 mm behind station 4 (optimum 830 mm); maximum 1860 mm between the aft edge of the mast marks and the forward edge of the 70 mm forestay marks
- Mast butt
- No fixed position. With runners at 16 LU, rake 1215 mm, uppers at MW and ram at zero, the mast should bend forward 30–40 mm at spreader height; never backwards. More than 40 mm: move the butt forward a hole.
- Mast butt, Petticrow (unverified by Fritz)
- Petticrow GRP: butt bolt in the 9th hole; bulkhead to mast-butt front face 195 mm, to mast centreline 245 mm. Petticrow cold-moulded: bulkhead to butt front face 145 mm.
- Runner set-up (heavy wind)
- Rake 1215 mm; each runner pulled to 16 LU; tape the wire at the deck outlet as the maximum mark; forestay should then read 33–35 LU
- Fixed jumpers
- 9–11 LU. Jumper brackets max 330 mm; the chord between the jumper wires should stand at least 30 mm off the mast; at 40 mm or more use adjustable jumpers
- Lowers vs uppers
- Lowers may be fairly tight but never more than 50% of the uppers (e.g. uppers 28 LU, lowers 12–14 LU)
- Ram travel
- Zero = mast front level with the aft edge of the 50 mm marks; may push forward up to 50 mm
Shroud tension by wind (Loos PT-2M, LU)
| Wind | Uppers, waves | Uppers, flat water | Lowers, waves | Lowers, flat water |
|---|---|---|---|---|
| LW 0–1.0 Bft | 9–10 | 11 | No tension | No tension |
| MW I 1.5–2.5 Bft | 11–13 | 12–14 | No tension | No tension |
| MW II 3.0–4.0 Bft | 14–16 | 13–18 | 5–6 | 5–7 |
| SW 4.5–8.0 Bft | 17–26 | 19–27 | 7–11 | 8–12 |
Runner mark height above deck, upwind (relative to the 16 LU maximum mark)
| Wind | Short guide | Detailed guide |
|---|---|---|
| 0–1 Bft | Loose – 200 mm | 220–200 mm |
| 1–2 Bft | 160–130 mm | 160–130 mm |
| 2–3 Bft | 130–100 mm | 130–90 mm |
| 3–4 Bft | 90–50 mm | 90–60 mm |
| 4–5 Bft | 40–30 mm | 60–30 mm |
| 5–6 Bft | 20–0 mm | 40–10 mm |
| 6+ Bft | — | 0 mm (mark on deck) |
Mast ram (mast control)
| Course / wind | Setting |
|---|---|
| Upwind 0–1 Bft | Ram 10–15 mm forward; backstay on |
| Upwind 1.5–4 Bft | Ram pulled fully back (minimum prebend) |
| Upwind 4+ Bft | Ram 10–15 mm forward (detailed text: 5–15 mm) with runners as tight as possible (16 LU) |
| Reach | Neutral, mast must not bend backwards (runner section: push mast 20–40 mm forward) |
| Downwind | 50 mm forward (maximum) |
Genoa set-up
| Wind | Leech to spreader tip (detailed table) | Foot distance off upper shroud (detailed table) | Foot touches shroud at height (short guide) |
|---|---|---|---|
| LW | 60–80 mm | Foot may just touch; max 30 mm off | About 30 mm above deck |
| MW I | 30–50 mm | 50–150 mm | 70–250 mm (all MW) |
| MW II | 30–50 mm | 200–250 mm | 70–250 mm (all MW) |
| HW | 80–120 mm | 300–500 mm | 250–450 mm |
Trim by condition
- Runners on a reach
- Mark above deck: LW 310 mm (detailed: 300 mm), MW 280–200 mm, HW 180–100 mm; mast 20–40 mm forward.
- Runners downwind
- Ease 680 mm with the ram fully forward (short guide); the detailed section gives 350–500 mm, about 450–500 mm on a run, with the fine-tune fully off.
- Runners in short chop
- In steep, short waves (Medemblik is the example) sail the runner mark about 20–30 mm higher than the table in every wind.
- Jumpers
- Slack to 1 Bft for twist; a little tighter at 1–2 Bft using lateral adjustment to straighten the head; central and tight at 2–4.5 Bft; ease a little from 5 Bft, keeping the masthead straight.
- Backstay
- Used for prebend up to 1 Bft (below about 3 kn use backstay instead of runners); otherwise a safety stay reaching and running.
- Mainsheet & traveller
- Top batten parallel to the boom; mark the sheet. Traveller centred up to 5 Bft; above 5.5 Bft 100 mm to leeward with hard sheet. Heel about 7–10°, not above 10–12° in heavy air.
- Outhaul
- Works in a 20–40 mm range (1:12 tackle). Light air: the fold along the foot just showing; 1.5–3.5 Bft flat water: fold clearly visible, ease in chop; 4+ Bft: full tension to the mark. Off the wind ease 80–100 mm (detailed: 60–80 mm running in light/medium air).
- Cunningham
- Keep a few horizontal folds up to 4 Bft; above 3.5 Bft in changeable wind err loose; light crews pull hard above 4.5 Bft.
- Boom vang
- No tension upwind; on a reach set so the top batten is parallel to the boom; ease downwind so the sail opens.
- Genoa lead
- Innermost position, about 360 mm in from the deck/hull edge (0–2 Bft); 340–300 mm at 3–4 Bft; 270–200 mm above 5 Bft, especially in chop. Fore-and-aft about station 8 (20–40 mm forward of it). Move out only on a reach.
- Genoa halyard
- Only enough to remove the crossing wrinkles; small wrinkles OK in light and medium air. 1:8 purchase recommended.
- Spinnaker
- Halyard eased about 200 mm reaching, 250 mm running; pole very low in very light air (about 850–1000 mm).
- The short guide and the detailed section give different runner marks and downwind runner eases; both are shown.
- Genoa figures also vary between sections: the short guide gives 30–60 mm leech-to-spreader in MW, section 3.5 gives 20–50 mm in MW and foot-to-shroud of max 50 / 100–200 / 250–350 / 400–500 mm (LW / MW I / MW II / HW), and the barber-hauler section gives foot heights of about 150–300 mm (MW) and 350–500 mm (HW).
- The rake procedure in section 3.4.2 measures with 25 LU on the forestay; the rigging checklist in section 4 uses 20 LU on the forestay with uppers at 18 LU.
- The detailed mast-butt procedure sets uppers/lowers to "MW I" at 18 / 10 LU, which doesn't match the 11–14 LU MW I upper figure in the short guide table.
- The lower-shroud figures are rough and refer to a new Petticrow mast; masts of different builders (and even the same builder) bend sideways differently, so check sideways bend while sailing.
- Copy hosted by US Sailing; no date or year is printed in the manual.
Høj Jensen Sails — Dragon Trimguide Current web page (undated)
- Written for
- Høj Jensen Dragon sails (not named in the trim guide; the separate Danish class page hojjensensails.dk/klassebaade/drage/ lists an MC2 all-round main, light/medium/hard genoas and a cross-cut or all-round spinnaker)
- Tension gauge
- Loos Gauge Model B; lowers measured without plastic, uppers with plastic
- How it’s measured
- Lay the forestay along the mast and mark it at the top of the black band; rake is the distance from that mark to the deck. Mast and forestay distances are measured from a straight line across the deck between the port and starboard station 4 marks; shroud positions are also measured from station 4, at 90° to the shrouds.
- Source
- Høj Jensen Sails, Current web page (undated)
Base setup
- Mast rake
- Light 121 cm; medium and heavy 122 cm
- Mast position (from station 4)
- 82 cm to the mast; 104 cm to the forestay
- Shroud positions (from station 4)
- Uppers (A) 81 cm; lowers (B) 84 cm
Rig tension (Loos Model B)
| Shroud | Light | Medium | Heavy |
|---|---|---|---|
| Lower shrouds (no plastic) | 0 | 7 | 12 |
| Upper shrouds (with plastic) | 12 | 17 | 25 |
- No wind speeds are given for light / medium / heavy, and jumpers, runners and mast ram aren't covered.
- The page places the station 4 sentence between the rake values and the mast distances, with no heading; it reads as the reference for the mast and forestay distances.
Petticrows (builder) — Petticrows – Rig set up guide 2011
- Written for
- Not sail-specific (builder's rig set-up for Petticrows Dragons; standard mast and new stiff "I" mast)
- Tension gauge
- Loos Model PT-2M, measured directly on the wire (named for the shroud tensions; the jumper and forestay steps just say Loos gauge)
- How it’s measured
- Mark the forestay where it meets a mark 81 cm up the mast from the deck (about the top of the black band); rake is from that mark to the deck with a little runner or backstay tension and the ram and shrouds disconnected. Positions measured from the station 4 line (about 1200 mm forward of the mast) taped across the deck.
- Source
- Petticrows (builder), 2011
Base setup
- Jumpers
- Fixed jumpers average 8 on the Loos gauge, set before stepping; adjustable systems: mark the control at 6, 8 and 10
- Mast rake
- Average 122 cm; light wind 121 cm; heavy wind 123 cm (change via forestay attachment hole)
- Upper shroud
- 82 cm, station 4 line to front face of the upper shroud
- Lower shroud
- 85 cm, station 4 line to front face of the lower shroud (lowers in the next hole aft)
- Forestay plate
- 104 cm, station 4 line to front of the forestay plate (plate 75 mm long); Petticrows put the forestay at the front of the plate
- Mast plate
- 82 cm, station 4 line to aft of the mast measurement plate (plate 50 mm long)
- J
- Max 186 cm (front of forestay plate to aft of mast plate)
- Mast step / prebend
- With rake at 122 cm and no ram or shrouds, push the mast aft: its front should be level with or aft of the aft end of the mast plate; prebend normally 0–10 mm. More than 10 mm behind: move the step pin forward; in front of the plate: move it aft.
- Initial shroud tension
- Uppers 15, lowers 10 (equal calibration marks both sides)
- Mast ram
- Set the bottlescrew so the mast front is level with the aft of the mast plate with the lever fully aft; forward travel must not pass the front of the plate (class max 50 mm)
- Maximum runner tension
- 32 measured on the forestay; mark the runner wire at the deck. 32 is the absolute maximum in strong winds.
- Older hulls
- Figures are for boats newer than 2008; older, less stiff hulls may need up to 30% more tension
Rig tension – standard mast (Loos PT-2M)
| Setting | Light | Medium | Strong |
|---|---|---|---|
| Lower shroud | 0 | 5–10 | 15 |
| Upper shroud | 12 | 15 | 20–25 |
| Upwind mast ram | 1–1.5 cm forward of max aft | Max aft | 1–1.5 cm forward of max aft |
Rig tension – new stiff "I" mast (Loos PT-2M)
| Setting | Light | Medium | Strong |
|---|---|---|---|
| Lower shroud | 0 | 5–8 | 10–12 |
| Upper shroud | 10 | 14–15 | 16–20 |
| Upwind mast ram | 1–1.5 cm forward of max aft | Max aft | 1–1.5 cm forward of max aft |
Trim by condition
- Shroud position
- Shrouds normally in line with the mast front upwind; moving them aft reduces mast bend, forward increases it.
- Lowers
- Lower figures are only a guide: sail upwind, sight up the mast and adjust until it is straight sideways.
- The guide writes the forestay reference as "81cm" but the class-rule note beside it says "max 81mm, min 79mm" – the mm is evidently a typo for cm.
- Station positions are those fitted to 2011 boats; on older Petticrows hulls check the plates and adjust by the same principles.
- No wind speeds are given for light / medium / strong.
- Copy hosted by US Sailing.
North Sails — Dragon Speed Guide Undated web article (a US Sailing PDF capture of it carries a 27 July 2020 creation date); North experts Ruairidh "Rory" Scott and Theis Palm
- Written for
- North Dragon range: crosscut and radial genoas (light to 10 kn, medium 6–18 kn, heavy 14–30 kn), mains for different masts, spinnakers
- Tension gauge
- Loos (refers to the North Tuning Guide for numbers)
- How it’s measured
- Q&A format; set forestay length first per the North Tuning Guide, then uppers and lowers to Loos numbers for your mast builder.
- Source
- North Sails, Undated web article (a US Sailing PDF capture of it carries a 27 July 2020 creation date); North experts Ruairidh "Rory" Scott and Theis Palm
Base setup
- Crew
- Weight limit 285 kg; most boats sail three (about 95 kg average)
- Sails
- Up to eight sails carded per event; most boats take four genoas, two mains, two spinnakers
Trim by condition
- Gear changing
- Runners are the main gear control: less runner in light air for headstay sag; as it builds, more runner with the ram fully back so the mast doesn't over-bend; windier still, lots of runner and ease the ram to bend the mast without losing headstay tension.
- Main upwind
- Boom near centreline, easing traveller slightly as the sheet comes on; no vang-sheeting. In bigger waves sail with more twist and softer sheet.
- Genoa lead
- Easing the barberhauler up moves the lead aft for a harder, flatter sheet; over 20 kn the second barberhauler pulls the lead a couple hundred mm further out.
- Downwind
- Furl the genoa, release the ram fully, ease runners to let the rig forward as far as the rules allow, ease the adjustable tack. From about 8 kn fly the spinnaker away from the short pole, guy up to six feet off it, pole squared to the shrouds and clews level; keep the top batten parallel to the boom.
- Tacking
- Don't release the genoa early – let it back against the rig first; in under 6 kn you can furl it in the tack.
- Gybing
- In breeze haul the new runner and ease the old as soon as possible; in light air the topmast backstay holds the rig. In 7–8 kn the guy stays at the pole; in 8–10 kn and up come out with the tack at the pole and ease it away.
- Mostly technique; it contains no shroud or runner tension numbers.
- Also available as a PDF capture on ussailing.org (wp-content/uploads/2020/07/northsails.com-Dragon-Speed-Guide.pdf); the old northsails.com/sailing/en/resources/dragon-speed-guide address redirects to the URL above.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Dragon resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Dragon by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Dragon class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesInternational Dragon Class Rules effective 2026-04-01 (per filename and search snippet)
- Class associationinternationaldragonsailing.net
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Dragon part