One-design race shop · Dinghy
International 505 Race Shop
Everything you need to prepare, compete, and win.
Fit verified for International 505
All International 505 equipment
15 parts
Fit verified for International 505
Harken
Harken Block - 16mm Single - Swivel
Part # HAR417
$31.95
$36.40Fit verified for International 505
Harken
Harken Slider Car - For Travelers: 7/8 in (22.0 mm) - Pinstop and Eyestrap
Part # HAR2750
$123.95
$141.20Fit verified for International 505
Harken
Harken Block - Carbo 29mm Single - Pivoting / 468 Cam-Matic
Part # HAR395
$78.95
$89.10Fit verified for International 505
Harken
Harken Block - Fly Block 18mm Single
Part # HAR2698
$25.95
$29.05Fit verified for International 505
Harken
Harken Block - Carbo T2 57mm Single
Part # HAR2152
$53.95
$61.60Fit verified for International 505
Harken
Harken Block - Carbo T2 40mm Single
Part # HAR2149
$44.95
$50.70Fit verified for International 505
Harken
Harken Block - 16mm Single - Eyestrap Assembly
Part # HAR442
$26.95
$30.45Fit verified for International 505
Harken
Harken Block - Carbo Ratchamatic 57mm Single - Swivel / Standard Grip (Black)
Part # HAR2625
$121.95
$138.30Fit verified for International 505
Harken
Harken Block - Carbo T2 29mm Single
Part # HAR2146
$29.95
$33.30Fit verified for International 505
Dynamic
Dynamic International 505 Dolly
Part # DYN-15026
$745.00
$1,015.91Fit verified for International 505
Nautalytics
Nautalytics Mast Mount Compass (Digital Compass)
Part # NTL-MASTMOUNT
$500.00
Fit verified for International 505
Nautalytics
Nautalytics Bulkhead Mount Compass (Digital Compass)
Part # NTL-BULKHEADMOUNT
$400.00
Fit verified for International 505
Velocitek
Velocitek Prism (Digital Dinghy Compass)
Part # VELPRISM
$579.00
No International 505 parts match these filters.
Can’t find a part for your International 505? Request a International 505 part
Official Harken dealer
International 505 deck layout
- Length
- 5.05 m (16'6")
- Beam
- 1.88 m (6'2")
- Weight
- 127.4 kg (280 lb)
- Main/Jib Area
- 14 sq. m (150.6 ft)
- Spinnaker Area
- 26 sq. m (280 sq ft)
Mainsheet
-
2
16mm Triple BlockHarken 408
$52.95 -
3
22mm Slider Car — Pinstop, EyestrapHarken 2750
$123.95 -
5
16mm Block — SwivelHarken 417
$31.95 -
7
18mm Fly Soft-Attach BlockHarken 2698
$25.95 -
8
29mm T2 Soft-Attach BlockHarken 2146
$29.95 -
10
29mm Pivoting Lead Block — Cam-Matic® cleatHarken 395
$78.95 -
11
29mm Pivoting Lead Block — Cam-Matic® cleatHarken 395
$78.95 -
12
57mm T2™ Soft-Attach BlockHarken 2152
$53.95 -
13
40mm T2™ Soft-Attach BlockHarken 2149
$44.95 -
14
18mm Fly Soft-Attach BlockHarken 2698
$25.95 -
16
40mm T2™ Soft-Attach BlockHarken 2149
$44.95 -
17
18mm Fly Soft-Attach BlockHarken 2698
$25.95 -
19
16mm Eyestrap BlockHarken 442
$26.95 -
20
57mm Ratchamatic® Block — SwivelHarken 2625
$121.95 -
21
16mm Cheek BlockHarken 416
$20.95
Systems and part numbers as published by Harken (checked 2026-11-04). Specifications are Harken’s; class rules decide what is legal for racing.
Go fast
International 505 tuning guide
505 tuning is a calibration game: rake (forward to the bow or aft to the transom), shroud tension and shroud-track position, mast ram at deck level, jib lead in/out and centreboard rake/lift, all stepped through the wind range. Each grid uses its own datum and scale (North's 0–7 rake numbers, Glaser's inches past 25′, P&B's millimetres to the inside transom floor, the German/Jess tables in metres), and shroud tension is a Loos gauge reading on the P&B sheets, a relative −/0/+/++ scale on the German tables, and unstated elsewhere.
Pinnell & Bax — 505 Tuning Guide February 2025 (PB-HEADOFICEFORMS-TUNINGGUIDES-02-2025-505)
- Written for
- P&B 505 sails; M2 or Alto mast
- Tension gauge
- Loos gauge on the shrouds (model not named)
- How it’s measured
- Rake from the top band on the mast to the inside of the transom floor. Spreader A: from the line between spreader ends perpendicular to the mast track; B: mast side wall to spreader end.
- Source
- Pinnell & Bax, February 2025 (PB-HEADOFICEFORMS-TUNINGGUIDES-02-2025-505)
Base setup
- Spreaders
- A 135–150 mm / B 390–410 mm, depending on crew weight
- Shrouds (base)
- 1 hole back
- Mast foot
- Aft of mast foot to transom station 11: 3065 mm
- Shroud base
- 2650 mm from the transom (neutral)
- Prebend datum
- 0–5 mm at spreader height at 7850 mm rake
Settings by wind (rig tension on Loos gauge)
| Wind (kn) | 0–4 | 4–8 | 8–12 | 12–17 | 17–22 | 22+ |
|---|---|---|---|---|---|---|
| Mast rake (mm) | 7850 | 7850 | 7850–7760 | 7760–7650 | 7650–7500 | 7450 |
| Rig tension (shrouds, Loos) | 30 | 30 | 30 | 30 | 32 | 33 |
| Shroud tracks | Forward 1 hole | 2650 | Aft 1 hole | Aft 1 hole | Aft 2 holes | Aft 2 holes + |
| Kicker | – | – | A bit | Yes | Loads | Loads |
| Cunningham | No | No | No | No | Yes | Yes |
| Jib fairleads from centreline (C/L of car) | 350 | 350 | 350–400 | 400–550 | 550–800 | 800 |
| Strut (from neutral/upright) | −40 mm | −30 to −10 mm | 0 | 10–20 mm | 20–30 mm | 30–40 mm |
| Jib luff tension | No creases | See creases | Just a hint of creases | No creases | Tension – a little | Tension – a little |
| Centreboard | 10° fwd in gybe | 10° fwd in gybe | Straight down in gybe | Raise 2–6 cm (more in chop) | Raise 7–10 cm (more in chop) | Raise 11–15 cm |
| Outhaul | Tight | Ease 15 mm | Ease 10 mm | Tight | Very tight | Very tight |
Trim by condition
- Kicker reasons
- 4–8 kn: stop the boom skying when tacking or easing; 8–17 kn: control twist; 17–22 kn: control twist and bend the mast; 22+: as much as you can handle.
- Fairlead figures have no unit on the sheet (presumably mm) and differ a lot from P&B's 2018 and 2012 grids (500–680+ and 400–610).
- Rig tension at 0–4 kn is 30 here but 32 in the 2018 and 2012 grids.
North Sails — 505 Tuning Guide (Ethan Bixby) and North Sails 505 Tuning Matrix Matrix updated 12/6/07; guide page posted 2017
- Written for
- North 505 sails designed by Ethan Bixby
- Tension gauge
- Not stated (shroud tension numbers 150–700, then max)
- How it’s measured
- Mast step: back of the mast along the top of the CB cap, over the transom to the aftmost point of the hull. Rake forward: jib halyard with the tape's zero at the top of the gooseneck band, taken forward to the top of the bow rail; datum 3′ 4″ forward = 25′ 8″ aft = '0'. Mark 1″ steps on the jib luff at the fork/eye junction. Negative numbers = less/forward, positive = more/aft.
- Source
- North Sails, Matrix updated 12/6/07; guide page posted 2017
Base setup
- Mast step
- As close to 10′ 0″ as you can while still getting the right low bend at max rake without hitting the partners (½–1″ forward is fine)
- Rake datum '0'
- 3′ 4″ forward / 25′ 8″ aft, shrouds snug, mast dead straight
- Spreaders
- 16.5″ long (shroud to nearest part of the mast) with 6.5″ poke; light teams and very light or very heavy air 7″ sweep; light teams can shorten to 16″. Assumes spreaders 124″ above deck.
- Centreboard datum
- Leading edge perpendicular to the hull = '0', marks every 1″ up the head; top of board to aft end of hull about 122″ with an HA board
- Jib lead datum
- In no wind at rake 0 and ram 0, sheet hard and align the sheet with the clew's more vertical line; that hole is '0'
505 North Sails Tuning Matrix (2007)
| Wind (kn) | Headstay # | Rake forward | Rake aft | Shroud tension | Mast at deck (in) | Mast at deck (mm) | West Coast ram | Centreboard | Vertical pin |
|---|---|---|---|---|---|---|---|---|---|
| 0–3 | 0 (datum) | 3′ 4″ | 25′ 8″ | 150 | −7/8 | −22 | 0 | Max forward | — |
| 6 | 0 | 3′ 4″ | 25′ 8″ | 150 | −5/8 | −15 | 1 | Max forward | — |
| 9 | 0 | 3′ 4″ | 25′ 8″ | 200 | −3/8 | −10 | 3 | Perpendicular | — |
| 12 | 1 | 3′ 5″ | 25′ 6″ | 300 | −2/8 | −6 | 4 | Perpendicular | — |
| 15 | 2 | 3′ 6″ | 25′ 3.5″ | 350 | −1/8 | −3 | 5 | ½″ | No gybe |
| 18 | 3 | 3′ 7″ | 25′ 2″ | 400 | 0 | 0 | 7 | 1″ | No gybe |
| 21 | 4 | 3′ 8″ | 25′ 1″ | 500 | 1/8 | 3 | 7.5 | 2″ | Up 2″ |
| 24 | 5 | 3′ 9″ | 24′ 11″ | 600 | 2/8 | 7 | 8 | 5″ | Up 2″ |
| 27 | 6 | 3′ 10″ | 24′ 8″ | 700 | 3/8 | 10 | — | 7″ | Up 3″ |
| 30 | 7 | 3′ 11″ | 24′ 6″ | Max | 4/8 | 13 | — | — | Max up |
Trim by condition
- Ram
- Set at 0 with the mast dead straight at 25′ 8″ and the rig just snug; positive is more ram down/aft.
- Jib lead
- Rake changes the lead angle for you, so heavy-air car moves may not be needed; move it aft for light air in flat water if needed. Calibrate sheet tension with a mark on the sheet against the seat tank.
- The matrix is linked from the 505 class site: https://int505.org/wp-content/uploads/2019/02/Current-North-Sails-Tuning-Grid.pdf
- The matrix also has a sparse 'imperial' column (−0.875 at 0–3, −0.25 at 12, 0.5 at 30) that duplicates the fractional deck-level values.
- The forward rake measurement is less sensitive to bend, shroud tension, rocker and transom height than the aft one.
Glaser Sails — Glaser Sails 505 Tuning Grid Sheet dated '5-05' (posted to the class site in Feb 2019)
- Written for
- Glaser 505 sails
- Tension gauge
- Not used for the grid; calibration at about 5 lb and 10–20 lb of rig tension
- How it’s measured
- Rake number = inches past 25′ from the main halyard (hoisted) to the bottom of the transom with the mast straight and about 5 lb of rig tension (8 = 25′ 8″). Ram marks are ¼″ steps on the mast (0 on top, 7 at the bottom), calibrated with rake at 25′ 8″, 10–20 lb tension and the ram set so the mast is straight at #7. CB = inches raised above the trunk/cap.
- Source
- Glaser Sails, Sheet dated '5-05' (posted to the class site in Feb 2019)
Glaser tuning grid
| Wind (kn) | 4 | 6 | 8 | 10 | 12 | 14 | 16 | 18 | 20 | 22 | 24 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Tacking angle, normal (°) | 86 | 84 | 84 | 86 | 88 | 92 | 96 | 98 | 100 | 102 | 104 |
| Tacking angle, flat water (°) | 82 | ||||||||||
| Reef | Reef 1 | Reef 2 | |||||||||
| Rake | 8 | 8 | 8 | 7 | 6 | 4 | 2 | 0 | 10 | 8 | 6 |
| Ram | 0 | 2 | 4 | 5 | 7 | 9 | 11 | 13 | 15 | 17 | 19 |
| CB (in raised) | .5 | 1 | 1.5 | 2 | 2.5 | 3 | 3.5 | ||||
| Vert | .5 | 1 | 1.5 | 2 |
Trim by condition
- Tacking angles
- Glaser lists expected tacking angles to calibrate a tactical compass.
- Rake numbers after 0 restart at 10, 8, 6, which reads as 24′ 10″, 24′ 8″, 24′ 6″, but the grid doesn't say so.
- The 'Vert' row isn't explained (possibly the vertical pin / board lift).
- 'Reef 1' and 'Reef 2' are printed in the tacking-angle cells of the 16 kn and 20 kn columns.
Pinnell & Bax — 505 Alto & M2 tuning guide 2018 (file name says 2016)
- Written for
- P&B 505 sails; Alto and M2 masts (the sheet doesn't name the spar makers)
- Tension gauge
- Not stated on this sheet (the 2012 Alto grid uses a Loos PRO gauge)
- How it’s measured
- Rake from the top band on the mast to the inside floor at the transom. Mast foot from the measurement station.
- Source
- Pinnell & Bax, 2018 (file name says 2016)
Base setup
- Prebend
- 5 mm at 7850 mm rake, shrouds 1 hole back of neutral
- Mast foot
- 3070 mm from station
- Shroud base
- 2650 mm from the transom (neutral)
Settings by wind
| Wind (kn) | 0–4 | 4–8 | 8–12 | 12–17 | 17–22 | 22+ |
|---|---|---|---|---|---|---|
| Mast rake | 7850 | 7850 | 7850–7760 | 7760–7650 | 7650–7500 | 7450 |
| Rig tension | 32 | 30 | 30 | 30 | 32 | 33 |
| Shroud tracks | Forward 1 hole | 2650 | Aft 1 hole | Aft 1 hole | Aft 2 holes | Aft 2 holes + |
| Kicker | – | – | A bit | Yes | Loads | Loads |
| Cunningham | No | No | No | No | Yes | Yes |
| Jib fairlead from centreline (C/L of car) | 500 | 450–500 | 450–520 | 520–610 | 610–68 (as printed) | 680+ |
| Strut | −30 | −10 | 0 | 10–20 mm | 20–25 mm | 25–30 mm |
| Jib luff tension | No creases | See creases | Just a hint of creases | No creases | Tension (a little) | Tension (a little) |
| Centreboard | 10° fwd in gybe | 10° fwd in gybe | Straight down in gybe | Raise 2–6 cm (more in chop) | Raise 7–10 cm (more in chop) | Raise 11–15 cm |
| Outhaul | Tight | Ease 15 mm | Ease 10 mm | Tight | Very tight | Very tight |
Trim by condition
- Kicker reasons
- Light air: stop the boom skying when tacking or easing; medium: control twist; heavy: control twist and bend the mast, as much as you can handle.
- The 17–22 kn fairlead cell is printed '610-68', probably 610–680 mm; the units of the fairlead and strut columns are mm only where shown.
Pinnell & Bax — 505 Alto rig tuning grid 2012
- Written for
- P&B 505 sails on the Selden Alto mast; crew weight 93 kg+
- Tension gauge
- Loos Pro gauge on the shrouds (printed 'Loose Pro-guage')
- How it’s measured
- Rake from the top band on the mast to the inside floor at the transom.
- Source
- Pinnell & Bax, 2012
Base setup
- Spreaders
- Length 385 mm, angle 134 mm, 3100 mm above the deck band
- Prebend
- Mast should have 5 mm
- Mast foot
- 3050 mm, as far back as is legal
- Shroud base
- 2650 mm from the transom (neutral)
Settings by wind (rig tension on Loos PRO gauge)
| Wind (kn) | 0–4 | 4–8 | 8–10 | 10–12 | 12–14 | 14–17 | 17–22 | 22+ |
|---|---|---|---|---|---|---|---|---|
| Mast rake (mm) | 7800 | 7820 | 7760 | 7730 | 7700 | 7675 | 7650 | 7565 |
| Rig tension (shrouds) | 32 | 30 | 30 | 30 | 30 | 32 | 32 | 33 |
| Shroud tracks | Forward 1 hole | 2650 | 2650 | Aft 1 hole | Aft 1 hole | Aft 2 holes | Aft 2 holes | Aft 2 holes |
| Kicker | No | No | A bit | Yes | Yes | Loads | Loads | Loads |
| Cunningham | No | No | No | No | No | No | Yes | Yes |
| Jib fairlead from centreline (C/L of car) | 400 | 400 | 450 | 520 | 530 | 570 | 570–610 | 610 |
| Strut (from neutral) | −6 to −10 mm | 0 | 0 | 0 | +6–10 mm | 12–15 mm | 20–25 mm | 25–30 mm |
| Jib luff tension | No creases | See creases | See creases | Just a hint of creases | No creases | No creases | Tension – a little | Tension – a little |
| Centreboard | 10° fwd in the gybe | 10° fwd in the gybe | 5° fwd in the gybe | Straight down in the gybe | Straight down or raise 1 cm | Raise 2–6 cm (more in chop) | Raise 7–10 cm (more in chop) | Raise 12–16 cm |
| Outhaul | Tight | Ease 10 mm | Ease 10 mm | Ease 10 mm | Ease 10 mm | Tight | Very tight | Very tight |
- Shroud-track cells span several columns in the PDF; they are repeated per column here based on their position.
- The 0–4 kn rake (7800) is shorter than 4–8 kn (7820) as printed.
- The strut cell for 0–4 kn is printed '-6 - 10mm' (read here as −6 to −10 mm, matching the '+6 - 10mm' style used at 12–14 kn).
Segelsport Jess — Tuning JESS 505 (M2 mast, BM mainsail) 2016–17
- Written for
- Mainsail 'BM'; mast 'M2' (abbreviations as printed)
- Tension gauge
- No gauge: shrouds on a relative scale (− loose, 0 just on, + tight, ++ very tight)
- How it’s measured
- Rake in metres (reference point not stated on the sheet). Shroud base car relative to neutral at 2.61 m.
- Source
- Segelsport Jess, 2016–17
Base setup
- Spreaders
- 420 mm (maybe 415 mm over 18 kn); sweep-back 150 mm
- Shroud base neutral
- 2.61 m
Settings by wind
| Wind | Very light, crew inside (Bft 0.5–1 / 3–5 kn) | Both on side tank (Bft 1–2 / 5–8 kn) | Bft 2–3 / 8–10 kn | Bft 3–4 / 11–14 kn | Bft 5 / 15–18 kn | Bft 6 / 20+ kn |
|---|---|---|---|---|---|---|
| Mast rake (m) | 7.88 | 7.87–7.86 | 7.80–7.75 | 7.75–7.68 | 7.68–7.60 | 7.60 and lower |
| Shrouds | + | − to 0 | 0 | + | + to ++ | ++ |
| Mast controller | Up for prebend | Neutral | Neutral / 1 cm down | 2 cm down | 3 cm down | 3–4 cm down |
| Jib in/out | 46.5 / 47 | 47 / 48 | 50 | 55 | 55–60 | 65 to all the way out |
| Jib block up/down (watch leech) | Totally loose / up | Still fairly loose | On / control leech | + (more down) | ++ | ++ |
| Shroud base car | Forward −5 cm | Neutral (2.61 m) | Neutral | +5 cm | +5 to +7 cm | +7 to +10 cm |
| Vang | Loose / off | Loose, but no slack | + | ++ | +++ | ++++ |
| Outhaul (+ = tight) | (legend only) | Ease 2–3 cm | Ease 1–2 cm | + | ++ | ++ |
- The sheet itself is headed only 'Tuning JESS 505'; it is attributed here to Holger Jess's JESS Segelsport (505 builder/rigger, Kiel) by inference from the name.
- Jib in/out has no unit on the sheet (values like 46.5–65, presumably cm from the centreline).
- In the outhaul row the first cell holds the legend '+ means tight' rather than a setting.
- An older Hunger/Jess 2001 world-champion trim guide (v1.3, 2003) is on the German class site: https://www.int505.de/Trimmanleitung-1-121.htm
German 505 class (unattributed) — Trimmtabelle für Boote Technikstand 2011 (BM09 Tecnora black mainsail, M2 mast) 2011 equipment (PDF made Dec 2012)
- Written for
- BM09 Tecnora black mainsail; M2 mast (as printed)
- Tension gauge
- No gauge: shroud tension on a relative scale (− loose, 0 lightly on, + firm, ++ very firm)
- How it’s measured
- Rake in metres (reference point not stated). Shroud chainplate (Pütting) position relative to neutral at 2.61 m. Wind in Beaufort.
- Source
- German 505 class (unattributed), 2011 equipment (PDF made Dec 2012)
Base setup
- Spreader length
- 42.0 cm
- Spreader sweep
- 140/145 mm
- Chainplate neutral
- 2.61 m
Settings by wind (German original, translated labels)
| Wind (Bft) | 0–1 (crew to leeward) | 1–2 (both on the side) | 2–3 | 3–4 | 5 | 6 |
|---|---|---|---|---|---|---|
| Mast rake (m) | 7.90–7.85 | 7.85 | 7.80–7.75 | 7.75–7.68 | 7.68–7.62 | 7.62–7.58 |
| Shroud tension | ++ | 0 | − | + | + to ++ | ++ |
| Mast controller | Max up | Neutral | Neutral + 1 cm down | Neutral + 2 cm down | Neutral + 3 cm down | Neutral + 3–4 cm down |
| Jib lead (in/out) | 47 | 47/48 | 50 | 52 | 52–55 | 55–60 |
| Jib lead up/down | Fully loose | Still loose | Start to pull down | + | ++ | ++ |
| Chainplate position | Slightly forward, −5 | Neutral (2.61 m) | Neutral | +5 cm | +5 to +7 cm | +7 to +10 cm |
| Vang | Fully loose | Fully loose | + | ++ | +++ | ++++ |
| Outhaul | + | −2 cm | −1 cm | + | ++ | ++ |
- Earlier edition of the same table format as the 2017 Jess sheet; rake, jib lead and shroud settings differ slightly (e.g. shrouds ++ in 0–1 Bft here versus + in 2017).
- Jib lead figures have no unit on the sheet (presumably cm from the centreline).
- The '−5' forward chainplate setting has no unit on the sheet (the other cells use cm).
- Headed with blank 'Speed / Höhe / Trainingspartner' fields for the sailor's own notes; no author is named.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
International 505 resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the International 505 by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current International 505 class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesInternational 505 Class Rules 2014, effective from 1 August 2014
- Class associationint505.org
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a International 505 part