One-design race shop · Keelboat
Squib Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Squib
All Squib equipment
26 parts
Fit verified for Squib
Forte
Forte Carbon Spinnaker Pole 1 1/2 in. Dia., 10 ft. max. length (for Boats 15-21 ft.) - UXP/UXP Ends
Part # FRTFCT150
$675.00
Fit verified for Squib
Forte
Forte Carbon Spinnaker Pole 1 1/4 in. Dia., 9 ft. max. length (for Boats 13-19 ft.) - RWO/RWO Ends
Part # FRTFCT125
$499.00
Fit verified for Squib
Nautalytics
Nautalytics Bulkhead Mount Compass (Digital Compass)
Part # NTL-BULKHEADMOUNT
$400.00
Fit verified for Squib
Ritchie
Ritchie Bracket Mount RitchieSport X-10W-M Compass (White Housing/Black Card)
Part # RIT-X-10W-M
$48.99
Fit verified for Squib
Ritchie
Ritchie Bracket Mount RitchieSport X-10B-M Compass (Black Housing/Black Card)
Part # RIT-X-10B-M
$51.99
Fit verified for Squib
Velocitek
Velocitek Mast Bracket for Prostart or SpeedPuck
Part # VELPROMMB
$69.00
Fit verified for Squib
Ronstan
Ronstan CleartStart Analogue Sailing Watch, 43mm - Unisex (Black/Red)
Part # RSGRF4056
$169.96
$199.95Fit verified for Squib
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for Squib
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for Squib
Davis Instruments
Davis Universal Masthead Mount f/WindTrak 10.Sport & WindTrak 15
Part # dav-1705
$59.99
Fit verified for Squib
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for Squib
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Squib
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for Squib
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for Squib
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for Squib
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95Fit verified for Squib
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95
No Squib parts match these filters.
Can’t find a part for your Squib? Request a Squib part
Go fast
Squib tuning guide
Squibs use pin-rack shrouds rather than turnbuckles, so tuning is about forestay length/rake, which hole the caps and lowers sit in, jib halyard versus forestay tension (luff sag) and the barber-hauler position. Hyde and Batt measure rake and mast heel differently and their settings are written for their own sails (Hyde 422 vs B3 differ too), so stick to one maker's method.
Hyde Sails — Hyde Squib Tuning Guide B3 (with B3 Additional Setup Notes 2025) October 2024; additional notes July 2025
- Written for
- Hyde B3 main and jib
- Tension gauge
- Not named in the B3 guide; its '(20)' figure matches the Loos-gauge reading the B3 trim guide quotes for the 422 jib luff (Loos model not stated). Shrouds set by pin-rack holes.
- How it’s measured
- Static base as in Hyde's 422 base-setting video: set the forestay length, then pin the shrouds just tight against it. 2025 rake check: main-halyard tape reading 1 m at the top of the lower black band, swung to the transom. Mast heel from the back of the mast to the front of the mainsheet track.
- Source
- Hyde Sails, October 2024; additional notes July 2025
Base setup
- Forestay / mast rake
- 206 cm (as in the base-setting video)
- Rake cross-check (2025)
- With the tape at 1 m on the top of the lower black band: 2215 mm to the top of the deck on centreline, 2720 mm to the bottom of the transom on centreline
- Mast heel (2025)
- 182 cm from the back of the mast to the front of the mainsheet track
- Barber-hauler holes
- 245 cm aft of the tack pin, 70 cm apart measured around the coach roof (2025 notes: 245 cm and 65 cm); fine-tune with the sheet-angle line on the jib
B3 tuning guide (2024)
| Setting | 1–6 kn | 7–11 kn | 10–15 kn | 15–22 kn | 22+ kn |
|---|---|---|---|---|---|
| Mast rake | 206 cm | 206 cm | Jib halyard | Jib halyard | Jib halyard |
| Jib halyard | Under tension compared to forestay | Tighten to match forestay | Set to sag + sheet-angle line | Base setting (20) | Base setting (20) |
| Rig tension | −0.5 hole from base | Base setting | +0.5 hole from base | +0.5 hole from base | +1 hole from base |
| Kicker | Slack | Tack up, slack/little on | Tack up, slack/little on | Max | Max |
| Outhaul | Tight | Eased 10 mm | Eased 10 mm | Max | Max |
| Jib luff | No | Slight crinkles | Slight crinkles | Remove creases | Remove creases |
| Jib barber | Max in | Ease 50 mm | Ease 50 mm | Ease if luff of main backing | Ease if luff of main backing |
| Main track | Max up | Max up | Max up to 100 mm down | Kicker sheet | Kicker sheet |
Shroud holes used at the 2025 Nationals (photo labels on the pin-racks, relative to the 422 video base; the photo does not say which plate is caps and which lowers)
| Wind (kn) | Plate with three labels (presumably caps) |
|---|---|
| 5–12 | +½ hole from base |
| 12–18 | +1 hole from base |
| 18+ | +1.5 hole from base (the other plate carries a single label, 18+ kn +½ hole, which fits the text's ½-hole lowers change in the windiest race) |
Trim by condition
- Rig tension (2025)
- B3 sails want slightly tighter shrouds than the 422 because less mainsheet is used; tighten shrouds rather than adding jib halyard as the wind rises. Changing holes needs the jib halyard released and backstay on to slacken the leeward shroud, and the reverse on the water.
- Lowers (2025)
- Set by sighting the mast in column sideways when trimmed upwind; moved ½ hole (4 mm) tighter only in the windiest race.
- Jib barber (2025)
- Run 50–100 mm eased from the hole, mostly about 70 mm (hole to base of block); going past 100 mm lowers the sheet angle too much.
- Jib halyard and sheet (2025)
- Match the jib luff-wire tension to the forestay, adding little as the wind builds. Sheet as hard as possible with the jib leech telltale always flying; mark the sheet at the cleat. With a 2:1 sheet, dead-end it at the deck-edge turning block, not the barber block.
- Main (2025)
- Second leech telltale stalled about 50% of the time; traveller can be max to windward until depowering. When overpowered, add shroud tension and start dropping the traveller; over about 18 kn a little backstay helps.
- Sheet-angle line
- New B3 jibs carry a sheet-angle line from the clew; owners can draw it through the clew eye and the front corner of the middle telltale window, and set the barber so the sheet lines up with it (B3 Sheet Angle Guide, 2024).
- The '(20)' in the jib-halyard row is not labelled in the B3 guide; it appears to be the Loos reading the B3 trim guide gives for the 422 jib luff (gauge model not stated).
- Hyde says the static base shown in its video matches this guide, but the jib-halyard tension used in the video is the one for stronger winds with B3 sails.
- The 2025 notes give the barber holes 65 cm apart; the 2024 guide says 70 cm.
- The 2025 additional notes are at https://www.hydesails.com/wp-content/uploads/2025/07/Squib-Tuning-B3-Update-2025.pdf.
Hyde Sails — Hyde Squib Tuning Guide 422 October 2024
- Written for
- Hyde 422 main and jib
- Tension gauge
- Loos for the '(20)' base (model not stated); shrouds by pin-rack holes
- How it’s measured
- Static base from Hyde's base-setting video (forestay length, then shrouds pinned just tight against it).
- Source
- Hyde Sails, October 2024
Base setup
- Forestay / mast rake
- 206 cm in 1–6 kn; above that rake is set with the jib halyard
- Barber-hauler holes
- 250 cm aft of the tack pin, 70 cm apart measured around the coach roof
422 tuning guide (2024)
| Setting | 1–6 kn | 7–11 kn | 10–15 kn | 15–22 kn | 22+ kn |
|---|---|---|---|---|---|
| Mast rake | 206 cm | Jib halyard | Jib halyard | Jib halyard | Jib halyard |
| Jib halyard | Under tension compared to forestay | Tighten to match forestay | Base setting | Base setting | Base setting |
| Rig tension | −1 hole from base | −0.5 hole from base | Base setting (20) | +0.5 hole from base | +1 hole from base |
| Kicker | Slack | Tack up, slack/little on | Straight main leech | Max | Max |
| Outhaul | Tight | Eased 10 mm | Eased 10 mm | Max | Max |
| Jib luff | No | Slight crinkles | Slight crinkles | Medium | Tight |
| Jib barber | Ease 100 mm | Ease 100 mm | Ease 50 mm | Ease 100 mm+ | Ease 100 mm+ |
| Main track | Boom mid-deck to outside edge of deck | Pull up to boom just below centre | Max up | Kicker sheet | Kicker sheet |
Trim by condition
- 422 vs B3
- The 422 rewards a firm main leech to straighten the jib luff; Hyde's B3 trim guide says the 422 jib luff is normally pulled on to 20 on a Loos gauge, with the barber about 100 mm eased in 15–18 kn.
- Here '(20)' sits in the rig-tension row; in the B3 guide it is in the jib-halyard row.
Hyde Sails — Hyde Squib B3 Trim Guide October 2024 (PDF metadata names Ben McGrane as author)
- Written for
- Hyde B3 main and jib
- Tension gauge
- Loos (model not stated) for the 422 comparison
- How it’s measured
- Jib luff sag judged from the depth of the top camber stripe.
- Source
- Hyde Sails, October 2024 (PDF metadata names Ben McGrane as author)
Base setup
- Jib luff sag
- Designed for 75–80 mm of sag at its optimum
- Forestay
- 206 cm (from the tuning video)
- Barber exit
- Moved 5 cm on the coach roof to suit the new sheet-angle line
Trim by condition
- Jib sag
- Run as much sag as possible without upper-leech flutter or a distorted top camber; if the helm can't steer to the jib the entry is too flat (too much sag). Straighten the luff with halyard or shroud tension only when overpowered.
- Main
- Shape is in the broad seam rather than the luff curve, so over-bending the mast (sheet, kicker or backstay) can starve it; the B3 main sets with more twist and wants less sheet. Keep the top leech telltale flying at least 50/50.
- Event set-up, 15–18 kn
- Base shroud hole, lowers set to hold the mast in column, barber eased 50 mm (where the 422 would be about 100 mm), jib luff softer than the 422's 20 on the Loos.
- Event set-up, 8–12 kn
- Shrouds half a hole tighter, forestay kept at 206 cm, barber moved forward. Little or no jib halyard from crew-to-leeward conditions up to two on the side, with the luff matching or just under forestay tension; halyard added only during long spells of hiking. Hyde judged the slightly more raked, higher-sheet-angle set-up the better one.
- Lighter air (4–8 kn)
- Suggests moving the shrouds 'up half a hole' so they are just shy of being in tension.
- Written as event notes from the 2024 UK Inlands; the B3 tuning guide above reflects these settings. The source labels Saturday as 15–18 kn and Sunday as 8–12 kn.
Batt Sails — Squib: Coaching Notes (with Spinnaker Hints) 2020.2
- Written for
- Batt Squib sails
- Tension gauge
- None; all settings by tape from the upper mast band
- How it’s measured
- Hoist a 10 m tape up the aft face of the mast until it reads 6325 mm down to the gooseneck black band, so the tape end is at the upper band; take all measurements from there to the stern deck at the transom.
- Source
- Batt Sails, 2020.2
Base setup
- Mast step
- Mast leaning gently on the aft face of the deck hole, shrouds slack: adjust the heel so the upper band to the deck centre at the transom is as close to 7470 mm as possible
- Cap shrouds
- Pull the mast forward and set the caps so the upper band to deck centre at the transom is 7570 mm; check the masthead is central (same to each transom corner)
- Lowers
- Mast held forward with the caps tight, no bend; lowers firm. On pin-racks, if in doubt choose the tighter hole.
- Jib halyard
- With the jib up and backstay holding the mast gently aft, set and mark the halyard at 7440 mm (upper band to back of the boat); a second mark at 7415 mm for very light and very heavy conditions
- Forestay
- About 30 mm of slack, taking no load on the more raked halyard setting
- Jib fairlead
- Barber-hauler hole 250 mm from centreline (C) and 2585 mm from the jib tack anchor (D); jib fairlead block 3015 mm from the tack anchor (E). Set correctly, the jib foot sits about 150 mm inside the rail, level with the mooring cleat.
Trim by condition
- Outhaul
- Tight upwind, clew to the band in very light air and when overpowered; in chop ease 20–40 mm in from the band. Reaching, ease up to 75 mm.
- Cunningham
- Light/medium: just enough to almost remove horizontal creases; more in strong winds to flatten and twist the upper leech. Release fully off the wind.
- Traveller
- Must reach the windward end so the boom can be centred; dump it in gusts and exit tacks with it down.
- Backstay
- Prebend the mast 40 mm in very light air; otherwise slack, used sparingly as a last resort in strong winds; off downwind.
- Mainsheet & vang
- Twist just enough for the upper telltales to fly; in strong winds flatten and twist with sheet, outhaul, cunningham and a little backstay. Almost no vang in very light air; downwind add vang if the boat rolls.
- Jib halyard
- Leave at position 1 in almost all conditions, easing to position 2 only in the lightest and most extreme winds; some crews ease it a lot in very strong winds for more rake. Downwind, backstay off and the mast pulled forward on the jib halyard.
- Barber hauler
- Pulled to its datum in light to moderate winds; ease it when the boom is further out in breeze or chop; ease almost to the shroud offwind.
- Spinnaker
- Set the outer pole end so the luff breaks evenly: raise it if the upper luff collapses first, lower it if the lower luff does; slightly lower in very light air; don't raise it in strong wind. Low-stretch sheets/guys help (Batt Spinnaker Hints 2023 repeats this).
- Hosted in the National Squib Association library; Batt's separate 'Squib Spinnaker Hints 2023' sheet (https://squibs.co.uk/wp-content/uploads/2023/04/SQUIB-SPINNAKER-HINTS-2023.pdf) has trim advice only.
- Section 5 says to keep the jib halyard 'as in 3(c)', but section 3 is the lowers; the forestay text ties its slack to the more raked halyard setting, i.e. the 7415 mm mark of step 4(d). The reference is ambiguous in the source.
- The document is marked © Batt Sails 2020; '2020.2' comes from the file name.
Hyde Sails — Squib Tuning Guide (Hyde, Jack Grogan) 2017 (file dated February 2018)
- Written for
- Hyde Squib sails of that period
- Tension gauge
- None; forestay, caps and inners given as steps from base (unit not stated, presumably pin-rack holes)
- How it’s measured
- Mast heel from the aft face of the mast at its base to the top of the transom, over the traveller (Squib 819).
- Source
- Hyde Sails, 2017 (file dated February 2018)
Base setup
- Mast heel
- 3522 mm (Squib 819)
- Forestay
- Lay the forestay and its chainplate down the front of the mast: base of the tenon to the bottom of the chainplate 13 cm
- Cap shrouds
- Find the base hole port then starboard while pulling slightly on the backstay; mast in the middle of the gate
- Inners (lowers)
- Pull the mast forward until it stops 2–5 mm from the front of the gate
Running rigging
| Wind (kn) | Main halyard | Jib halyard | Kicker | Outhaul | Cunningham | Jib cunningham | Barbers | Traveller | Mainsheet tension |
|---|---|---|---|---|---|---|---|---|---|
| 5–9 | 1 cm down | Loose | Slack | Ease 1 cm | Off | Slight tension | In | Up | Centre |
| 10–14 | Black band | Base | Snug | Hard | Off | Moderate | In – 3 cm out | Up | Centre |
| 15–20 | Tight | Tight | Hard | Hard | Trimmed | Hard | 5–10 cm out | ¼–½ down | Centre–¼ |
| 20+ | Tight | Tight | V. hard | Hard | Hard | Hard | 10–25 cm out | ½ down | ¼–½ down |
Standing rigging (steps from base; the chart does not name the unit)
| Wind (kn) | Forestay | Caps | Inners |
|---|---|---|---|
| 5–9 | Down 1 | Base | Base |
| 10–14 | Base | Base/down 1 | Base/down 1 |
| 15–20 | Plus 1 | Down 2 | Down 1 |
| 20+ | Plus 1 | Down 2 or 3 | Down 1 or 2 |
- Older Hyde chart kept in the class library; superseded by Hyde's 2024 422/B3 guides, which use a different base method.
Chris Hogan — Chris Hogan's Tuning Guide (from his talk at Alexandra Palace) Undated (posted 2023)
- Written for
- Batt sails (the author thinks the settings may not suit Hyde sails)
- Tension gauge
- None (hand tight)
- How it’s measured
- Rake set from boom height above the aft deck; mast foot measured directly from the near side of the mainsheet traveller to the rear pin.
- Source
- Chris Hogan, Undated (posted 2023)
Base setup
- Mast rake
- Underside of the boom 400 mm above the aft deck when sheeted hard; set the forestay to suit
- Cap shrouds
- One side fixed; the other needs a little backstay to locate the pin (hand tight)
- Lowers
- Set in about force 2 with the crew on the same side, for a straight mast
- Mast foot
- 1815 mm from the near side of the mainsheet traveller to the rear pin
- Jib barbers
- Light air: centreline to bearing surface 245 mm; force 2–4: 328 mm; centreline to deck exit 240 mm
Trim by condition
- Outhaul
- Beating tight to the black band; reaching off 50 mm.
- Cunningham
- On tight in windy conditions.
- Rig tension
- Crew on the same side: hand tight; crew sitting opposite: pull on 20 mm tighter.
- Backstay
- Listed as n/a.
- A one-page summary of a talk; the PDF metadata names Dick Batt as the file's author (created June 2023). Not a sailmaker-published guide.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Squib resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Squib by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Squib class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesNational Squib Class Rules, uploaded Dec 2022; filename suggests 18 Feb 2022 (unconfirmed)
- Class associationsquibs.co.uk
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Squib part