One-design race shop · Dinghy
Wayfarer Race Shop
Everything you need to prepare, compete, and win.
Fit verified for Wayfarer
All Wayfarer equipment
22 parts
Fit verified for Wayfarer
Nautalytics
Nautalytics Bulkhead Mount Compass (Digital Compass)
Part # NTL-BULKHEADMOUNT
$400.00
Fit verified for Wayfarer
Rooster
Rooster Tell Tales - Teflon Coated (3 Green & 3 Red)
Part # ROO127491
$8.96
$9.95Fit verified for Wayfarer
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Black/Grey)
Part # RSGRF4055A
$101.96
$119.95Fit verified for Wayfarer
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Blue/Grey)
Part # RSGRF4055B
$101.96
$119.95Fit verified for Wayfarer
Davis Instruments
Davis Universal Masthead Mount f/WindTrak 10.Sport & WindTrak 15
Part # dav-1705
$59.99
Fit verified for Wayfarer
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Red)
Part # RSGRF4054-RED
$84.96
$99.95Fit verified for Wayfarer
Ronstan
Ronstan Tell Tales - Tell Tails Kit (3 Pairs)
Part # RONRF4025
$9.91
$11.66Fit verified for Wayfarer
Ronstan
Ronstan Tell Tales - Leech Tails Kit (3 Pairs)
Part # RONRF4026
$9.91
$11.66Fit verified for Wayfarer
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Blue)
Part # RSGRF4054-BLU
$84.96
$99.95Fit verified for Wayfarer
Ronstan
Ronstan CleartStart Sailing Watch, 50mm - Unisex (Red/Grey)
Part # RSGRF4055
$101.96
$119.95Fit verified for Wayfarer
Ronstan
Ronstan ClearStart Race Timer - Unisex (Black)
Part # RSGRF4050
$118.96
$139.95Fit verified for Wayfarer
Ronstan
Ronstan ClearStart Sailing Watch, 40mm - Unisex (Black)
Part # RSGRF4054-BLK
$84.96
$99.95
No Wayfarer parts match these filters.
Can’t find a part for your Wayfarer? Request a Wayfarer part
Go fast
Wayfarer tuning guide
Wayfarers are tuned with shroud length (rake), spreader length and angle (prebend), mast chocks and around 300–400 lb on the shrouds, with rake raked back and the board lifted as the wind builds. Rake numbers are not comparable between guides without checking the datum: P&B reads a 23′5″–23′11″ tape to the top of the transom (and splits Mk4 from Hartley boats), North gives 23′8″–23′10″ without a datum, and the class-hosted McNamara and Uncle Al articles measure 23′2″–23′7″ to the mainsheet traveller.
Pinnell & Bax — Wayfarer Tuning Guide 2025 (PB-HEADOFICEFORMS-TUNINGGUIDES-2025-WAY)
- Written for
- P&B Wayfarer mainsail, genoa and spinnaker
- Tension gauge
- Super Spar rig gauge on the shrouds, lb
- How it’s measured
- Rake: pull a tape to the top of the mast and raise or lower it until 19′3″ reaches the top of the gooseneck black band, then take the tape to the back of the boat and read it at the top of the transom. Spreaders: A is the deflection (line between the spreader ends to a perpendicular from the mast track); B is the length from the side wall of the mast to the spreader end. Prebend is measured at spreader height.
- Source
- Pinnell & Bax, 2025 (PB-HEADOFICEFORMS-TUNINGGUIDES-2025-WAY)
Base setup
- Mast
- Selden E
- Crew weight
- 23–26 stone
- Spreader deflection (A)
- 220 mm
- Spreader length (B)
- 520 mm; shorten B by ½″ for a lighter crew, lengthen it by the same for a heavier crew
- Prebend
- 26 mm at spreader height once rake and tension are set; adjust the spreaders fore or aft to get it
- Genoa track
- 21″ from the centreline, 300 mm long; the sheeting angle should bisect the clew from a point 1.4 m up the jib luff
- Spinnaker pole
- 6′6″ (class maximum); lift the pole eye 8″ up the mast to increase its effective length
Rake and rig tension, boats up to Mk4 (Super Spar gauge)
| Wind | Mast rake | Rig tension |
|---|---|---|
| Light | 23′7″ / 7180 mm | 300 lb |
| Medium | 23′6″ / 7160 mm | 340 lb |
| Heavy | 23′5″ / 7140 mm | 350 lb |
Rake and rig tension, Hartley boats (Super Spar gauge)
| Wind | Mast rake | Rig tension |
|---|---|---|
| Light | 23′11″ / 7290 mm | 350 lb |
| Medium | 23′10″ / 7265 mm | 400 lb |
| Heavy | 23′9″ / 7240 mm | 400+ lb |
Mast chocks (rake shown for Mk4 or Hartley)
| Wind | Mast rake | Chocks |
|---|---|---|
| Light | 23′7″ / 7180 mm or 23′11″ / 7290 mm | 49 mm |
| Medium | 23′6″ / 7160 mm or 23′10″ / 7265 mm | 52 mm |
| Heavy | 23′5″ / 7140 mm or 23′9″ / 7240 mm | 56 mm |
Mainsail outhaul and cunningham
| Wind | Outhaul upwind | Outhaul reaching/off wind | Cunningham upwind | Cunningham reaching/off wind |
|---|---|---|---|---|
| Light | Tight | Ease 12 mm (½″) | Off | Off |
| Medium | Ease 18 mm (¾″) | Ease 90–115 mm (3½–4½″) | Pull up to 12 mm (½″) | Off |
| Heavy | Tight | Ease 50–75 mm (2–3″) | Pull up to 75 mm (3″) | Off |
Trim by condition
- Rig tension
- Use enough to stop the jib luff sagging; sailing upwind, the leeward shroud should be just slack.
- The rake tables are split by hull: the Hartley figures are 100–110 mm (4″) longer than the up-to-Mk4 figures for the same wind (the sheet labels the first table 'Up to M4').
- Wind ranges are named only as light, medium and heavy; no knot figures are given.
- The crew-weight note says to change measurement B (spreader length) by ½″, although B is printed in mm.
North Sails — Wayfarer Tuning Guide 2014 2014 (PDF properties: 'Wayfarer Tuning Guide 2013', author Tim Rush)
- Written for
- North Sails Wayfarer sails (no models named)
- Tension gauge
- Not stated; tension is measured on the shroud, in lb
- How it’s measured
- Rig tension measured on a shroud. The rake datum is not stated. Jib sheeting lines are measured down the luff from the head.
- Source
- North Sails, 2014 (PDF properties: 'Wayfarer Tuning Guide 2013', author Tim Rush)
Base setup
- Spreaders
- 520 mm long; 940 mm between tips
- Jib sheeting lines
- Lower line 1880 mm and upper line 2320 mm down the luff from the head: the steeper line is for medium conditions, the shallower one for light and heavy winds
Settings by wind
| Control | Light winds | Moderate winds | Strong winds |
|---|---|---|---|
| Mast rake | 23′10″ | 23′9″ | 23′8″ |
| Prebend | 29 mm | 24 mm | 35 mm |
| Rig tension | 400 lb | 300 lb | 400 lb |
| Chocks | Neutral | Neutral | Neutral |
| Fairleads | Inside track | Middle/outside track | Outside track |
| Cunningham | Upwind none; downwind none | Upwind just remove wrinkles; downwind none | Remove wrinkles then pull hard; reach just remove wrinkles |
| Outhaul | Pull on full, then ease 2 cm | On enough to keep the base of the main flat | Full |
| Centreboard | Full down | Up 2–3″ | Up 4–6″ |
Trim by condition
- Rig tension
- Extra tension in light air is there to add prebend; once both crew are hiking, use just enough that the leeward shroud goes slack.
- Jib track
- Move to the outside fairlead track once the wind holds the boom 20 cm or more off the centreline, so the jib can be sheeted flat without closing the slot.
- Outhaul
- Ease downwind for power.
- Centreboard
- Upwind, raise the board as you rake the mast back to keep the helm balanced.
- Light-air tension (400 lb) is higher than moderate (300 lb) on purpose, to bend the mast.
- The file name and title say 2014, but the PDF's own properties call it the 2013 guide.
McNamara Sails (Mike McNamara) — Mike McNamara's Complete Guide to Sail Trim and Sail Care (Mainsail, Genoa, light/medium/heavy set guides) Undated web articles (with notes by the site editor, 'Uncle Al')
- Written for
- McNamara Wayfarer mainsail and genoa
- Tension gauge
- Not stated; windward-shroud tension in lb
- How it’s measured
- Rake measured ashore in a straight line from the masthead black band to the centre of the mainsheet traveller (its lower forward edge), with about 330 lb on the rig and the mast prebent; Al's alternative uses a tape on the main halyard to the forward underside edge of the traveller centre. Spreader tip-to-tip is measured shroud to shroud across the back of the mast. Genoa fairlead distances are to the inside of the transom.
- Source
- McNamara Sails (Mike McNamara), Undated web articles (with notes by the site editor, 'Uncle Al')
Base setup
- Mast rake
- 23′5½″–23′6½″ in force 2–3 (5–10 kn)
- Spreaders
- 1′8″ long; 3′2″ tip to tip (shroud to shroud) across the back of the mast
- Prebend
- About 1½″ at the spreaders
- Main halyard
- Hook #3 on the halyard rack (editor's boat)
- Vang angle
- About 45° to both mast and boom
- Genoa track
- Track centre 2350 mm from the inside of the transom and 530 mm from the centreline, parallel to the seat edge; track 300 mm long
- Jib halyard (shore check)
- About 330 lb
Rig tension on the windward shroud (gauge not stated) and genoa fairlead
| Wind | Rig tension | Fairlead bearing surface to transom |
|---|---|---|
| Light | 300–330 lb | 2400 mm |
| Medium (force 2–3) | 330–350 lb | 2380 mm |
| Heavy | 350–360 lb | 2350 mm |
Sail set guide by wind and sea (qualitative)
| Control | Light, flat | Light, chop | Medium, flat | Medium, chop | Heavy, flat | Heavy, chop |
|---|---|---|---|---|---|---|
| Rig tension | Medium | Medium slack | Medium tight | Medium | Very, very tight | Very tight |
| Jib fairlead / sheet | Forward, sheet eased | Well forward, sheet medium eased | Middle, sheet medium | Middle, sheet medium | Aft, sheet medium | Middle, sheet medium |
| Mainsheet / boom end | Boom eased, leech eased | Boom eased, leech eased | Boom inboard, leech medium | Boom slightly eased, leech medium tight | Boom out, leech very tight | Boom out, leech tight |
| Cunningham | Nil | Nil | Nil to minute | Nil to minute | Medium | Medium |
| Kicker / vang | Very light (editor: reaches and runs only) | Light (editor: reaches and runs only) | Moderate | Medium | Tight to very tight | Very tight |
| Main foot | Very tight | Slightly eased | Slightly eased | Well eased | Tight | Tight |
| Mast bend | No chocks, prebend | Slightly chocked, prebend | Very chocked, mast straight | Very chocked, mast straight | Chocked, mast bent | Medium chocked, mast bent |
| Trim | Minute heel, weight forward | Minute heel, weight forward | Upright, weight central | Very upright, weight central | Upright, weight central | Upright, weight aft |
Trim by condition
- Rake by wind
- Shorten the black-band-to-traveller distance by 2–4″ in stronger wind and lengthen it by 1–2″ in lighter wind, by moving the shroud ends 1–2 holes on the shroud plates.
- Chocks
- None in light winds; maximum in medium air, taking them out as the mainsheet is eased. Several small chocks are better than one large one.
- Mast gate
- A quarter inch of play at the gate can move the spreader tips more than two inches.
- Main foot
- Ease about 1½″ as soon as the crew sits out, to allow a little backwinding.
- Main leech
- Don't oversheet: the last 6″ or so of the top batten should line up with the last two feet of the boom. Use the cunningham lightly, only to clear luff creases, and whenever the vang comes off, take the cunningham off too.
- Genoa sheeting
- Set the fairlead so all three windward tufts (about 10 cm long, about 15 cm from the luff) break together. Every 1″ of sheet through the fairlead moves the middle leech about 5″. Mark light, medium and heavy lead positions on the track (heavy: move aft until the ¾-height tuft collapses, then about 1″ forward) and never put the lead aft of the heavy mark; mark the sheet near the fairlead too. When in doubt, ease.
- Genoa halyard
- Leeward shroud just taut; ease the halyard slightly in light weather to add luff sag.
- Hosted on the Wayfarer International site (WIT section), not on a McNamara site; the articles are undated.
- Spread over several WIT pages: MacMainsail.htm (rake, prebend, spreaders, chocks), MacGenoa.htm (track, fairlead and tension figures) and MacSailSetGuideLight/Medium/Heavy.htm (the set-guide table), all in the same MikeMac folder.
- Force 2–3 is given as 4–10 kn in one paragraph of the mainsail article and 5–10 kn in the rake paragraph.
- The 'reaches and runs only' qualifier on the light-air vang settings is the site editor's note, not McNamara's.
Wayfarer International (WIT articles by 'Uncle Al') — Mast/Main Combination simplified; Tuning the Wayfarer mast; the W Magic Numbers Undated web articles (the Magic Numbers page cites UKWA tuning numbers posted in May 2001)
- Written for
- Not sail-specific (written around the editor's own boat, SHADES)
- Tension gauge
- Not stated; rig tension in lb
- How it’s measured
- Rake: shackle a 25′ tape to the main halyard, hoist it to the 'main fully up' hook with the mast pushed forward (prebent), and read it at the centre of the traveller's lower forward edge. Mast centring: compare the halyard tape to each transom corner (within ¼–½″). Spreader length is from the side of the mast to the inside edge of the shroud; tip spacing is shroud to shroud.
- Source
- Wayfarer International (WIT articles by 'Uncle Al'), Undated web articles (the Magic Numbers page cites UKWA tuning numbers posted in May 2001)
Base setup
- Mast rake
- 23′5″–23′6″ for light and medium air at about 330 lb (the mast-tuning page gives 23′5″–23′7″); survival 23′2″
- Heavy-air rake
- Drop one hole on the shroud plates for 23′2″–23′3″ (the page calls one hole 'about ¼ inch', which can only be the step at the plate, not the change in rake)
- Shroud plates
- A single row of holes changes rake about 4″ per hole; two staggered rows about 2″
- Spreader length
- 1′8″ (20″–20½″ on the mast-tuning and Magic Numbers pages)
- Spreader tip spacing
- 38″ in medium air for 2–3″ of bend with the mast fully chocked; 39″ or more in heavy air; less than 38″ in light air is possible but rarely used. Never angle the spreaders forward of the mast.
- Mast bend
- 2–3″ at spreader height in average conditions; up to 4″ in very light air (no front chocks, heavy-air rig tension with a forestay take-up tackle); 4–6″ using the vang when consistently overpowered; 4+″ in survival
- Rig tension
- About 330 lb at medium tension; usually just enough to take visible slack out of the lee shroud close-hauled
- Outhaul
- Normally 3–4″ off the black band; fully out only in very light or heavy air
- Jib lead
- Track about 20½″ from the centreboard box at its aft end (Magic Numbers: sheeted to a point 20.5″ from the middle of the centreboard slot); lead about 3½″ forward of the front edge of the centre thwart
- Leech ticker
- One 6″ wool tuft at about ¾ leech height
Trim by condition
- Chocks
- Fully chocked both sides to remove play; front chocks out in light air. Many racers add a front chock at deck level in medium breeze to reduce low bend and add power.
- Spreader adjustment
- Start with both spreaders at the same angle (sight up the shrouds from 10–15′ off the side), then change both by the same number of half turns.
- Cunningham
- Only enough to remove major luff creases as the wind builds.
- Jib halyard
- Over-tension for the conditions, then ease until the tickers settle and the groove is wide enough; when in doubt, let it out.
- Boom
- With no mainsheet tension the boom should hang parallel to the water at normal rake; at survival rake it angles down toward the transom.
- Four overlapping pages in the WIT UncleAl folder: 98MastMain.htm (linked), 03TuningtheWmast.htm (mast-tuning page), 98MagicNumbers.htm and 98Genoa.htm (jib lead). Where they differ (rake 23′5″–6″ vs 23′5″–7″; spreader length 1′8″ vs 20–20½″) both are shown.
- The heavy-air note says one shroud-plate hole is 'about ¼ inch'. That cannot be the rake change: the same sentence takes rake from 23′5″–6″ to 23′2″–3″ (about 3″), and the mast-tuning page gives about 4″ of rake per hole (2″ on staggered plates). Read the ¼ inch as the shroud-length step and use the rake figures.
- No author is named on the pages beyond 'Uncle Al'.
Settings are summarised from each sailmaker’s published guide (checked 2026-11-02). Use the guide written for your sails, check it against the full guide, and stay inside the class rules.
Technical
Wayfarer resource centre
How we verify parts
- Fit verified
- Each part listed here was matched to the Wayfarer by part number against the builder’s specification or a manufacturer’s class guide, then checked again by an independent reviewer.
- Class rules
- Fitting a part is not the same as it being legal for racing. Read the current Wayfarer class rules before changing equipment, and ask your class measurer if a part is not original equipment.
- Class rulesWayfarer International Class Rules, updated 14 April 2023, effective 1 April 2023
- Class associationwayfarer.org.uk
- Racing guideThe right gear for the right application
- Racing guideWhat to do when rounding the mark
- Racing guideHow to conquer the layline
- Rigging helpRequest a Wayfarer part